CAN COMMUNICATION SYSTEM > Check CAN Bus Lines for Short Circuit (RHD Models) |
| Symptom | Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω. |
|


| 1.CHECK FOR SHORT IN CAN BUS LINES (DLC3 BRANCH LINE) |
Disconnect the cable from the negative (-) auxiliary battery terminal.
![]() |
Disconnect the DLC3 branch line connector (I96) from the CAN junction RH connector.
| *a | Rear view of wire harness connector (to CAN Junction RH Connector) |
| *b | to DLC3 |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | |
| 2.CHECK FOR SHORT IN CAN BUS LINES (BRANCH LINE) |
Reconnect the DLC3 branch line connector (I96) to the CAN junction RH connector.
![]() |
Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.
| *1 | DLC3 |
While observing the resistance value shown on the tester, disconnect connectors (I95, I102, I103, I100, I107, I106, I110, I97, I173, I109 and I111) from the CAN junction LH connector or CAN junction RH connector one by one until the resistance becomes normal (between 54 and 69 Ω).

| *A | Separate Type Yaw Rate Sensor | - | - |
| *1 | Power Management Control ECU | *2 | Main Body ECU (Multiplex Network Body ECU) |
| *3 | Air Conditioning Amplifier Assembly | *4 | Airbag Sensor Assembly |
| *5 | Power Steering ECU Assembly | *6 | ECM |
| *7 | Radio and Display Receiver Assembly | *8 | Combination Meter Assembly |
| *9 | DLC3 | *10 | Smart Key ECU Assembly (Certification ECU) |
| *11 | Brake Booster with Master Cylinder Assembly (Skid Control ECU) | *12 | Steering Sensor |
| *13 | Clearance Warning Assembly ECU | *14 | Yaw Rate Sensor |
| *15 | CAN Junction RH Connector | *16 | CAN Junction LH Connector |

| *a | Component without harness connected (CAN Junction LH Connector) | - | - |
| CAN Junction LH Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
| CAN main bus line (bus line connecting CAN junction LH connector and CAN junction RH connector) | I93 | B | W |
| Radio and display receiver assembly | I107 | R | W |
| ECM | I104 | G | W |
| Power steering ECU assembly | I100 | L | W |
| Airbag sensor assembly | I103 | Y | W |
| Air conditioning amplifier assembly | I102 | V | W |
| Main body ECU (Multiplex network body ECU) | I95 | P | W |
| Power management control ECU | I109 | BE | W |

| *a | Component without harness connected (CAN Junction RH Connector) | - | - |
| CAN Junction RH Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
| Yaw rate sensor*1 | I173 | BE | W |
| Clearance warning ECU assembly | I111 | P | W |
| Steering sensor | I97 | V | W |
| Brake booster with master cylinder assembly (Skid control ECU) | I110 | Y | W |
| Smart key ECU assembly (Certification ECU) | I106 | L | W |
| DLC3 | I96 | G | W |
| Combination meter assembly | I94 | R | W |
| CAN main bus line (bus line connecting CAN junction LH connector and CAN junction RH connector) | I101 | B | W |
| Symptom | Proceed to |
| The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of branch lines.) | A |
| The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.) | B |
When there is a short in one or more of the branch lines:
Reconnect all of the connectors to the CAN J/C, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.
|
| ||||
| A | |
| 3.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN BUS LINE) |
![]() |
Disconnect the combination meter assembly main bus line connector (I94) from the CAN junction RH connector.
| *a | Rear view of wire harness connector (to CAN Junction RH Connector) |
| *b | to Combination Meter Assembly |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *1 | DLC3 |
| Symptom | Proceed to |
| The resistance is still below 54 Ω when the combination meter assembly connector is disconnected. (There are no shorts in the combination meter assembly or between its main bus lines.) | A |
| The resistance falls within the specified range (between 108 and 132 Ω) (the other terminating resistor is normal) when the combination meter assembly connector is disconnected. (There is a short in the combination meter assembly or between its main bus lines.) | B |
|
| ||||
| A | |
| 4.CHECK FOR SHORT IN CAN BUS LINES (ECM MAIN BUS LINE) |
![]() |
Disconnect the ECM main bus line connector (I104) from the CAN junction LH connector.
| *a | Rear view of wire harness connector (to CAN Junction LH Connector) |
| *b | to ECM |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| *1 | DLC3 |
| Symptom | Proceed to |
| The resistance is still below 1 MΩ when the ECM connector is disconnected. (There are no shorts in the ECM or between its main bus lines.) | A |
| The resistance becomes 1 MΩ or more when the ECM connector is disconnected. (There is a short in the ECM or between its main bus lines.) | B |
|
| ||||
| A | |
| 5.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C RH) |
![]() |
Disconnect the CAN main bus line connector (I101) from the CAN junction RH connector.
| *a | Rear view of wire harness connector (to CAN Junction RH Connector) |
| *b | to CAN Junction LH Connector |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | |
| 6.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C LH - CAN J/C RH) |
Reconnect the CAN main bus line connector (I101) to the CAN junction RH connector.
![]() |
Disconnect the CAN main bus line connector (I93) from the CAN junction LH connector.
| *a | Rear view of wire harness connector (to CAN Junction LH Connector) |
| *b | to CAN Junction RH Connector |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||
| 7.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR) |
Reconnect the connector for the short-circuited branch line to the CAN J/C (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).
Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the short-circuited branch line is connected (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||
| 8.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY) |
Reconnect the combination meter assembly main bus line connector (I94) to the CAN junction RH connector.
Disconnect the combination meter assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||
| 9.CHECK FOR SHORT IN CAN BUS LINES (ECM) |
Reconnect the ECM main bus line connector (I104) to the CAN junction LH connector.
Disconnect the ECM connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||