Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)

DTC    B2271    Ignition Hold Monitor Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction in the IG1 circuit, IG2 circuit or IG hold circuit in the power management control ECU is detected.

HINT:
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2271
When either of the following conditions is met (1-trip detection logic*):
  1. The IG1 or IG2 circuit in the power management control ECU is malfunctioning.
  2. The IG hold circuit in the power management control ECU is malfunctioning.
  1. AM2 fuse
  2. Power management control ECU
  3. Wire harness or connector
Turn the power switch on (IG).

HINT:
To turn the power switch on (IG), carry the electrical key transmitter sub-assembly and press the power switch twice with the shift lever in P and the brake pedal released.

  1. *: Only detected while a malfunction is present and the power switch is on (IG)

HINT:
  1. The IG1 and IG2 circuits activate the IG1 and IG2 relays.
  2. After the IG1 and IG2 circuits turn on, even if the CPU operates incorrectly, the IG hold circuit maintains the power source mode in on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
The power switch cannot be turned on (IG) (the hybrid control system cannot be started).
The power source mode cannot be changed to on (IG).

WIRING DIAGRAM


B298920E02


INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
    for Power Source Control: Body / Power Source Control / DTC.
    for Entry&Start: Body / Entry&Start / DTC.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  4. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


HINT:

Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
B2271
Power Source Control
  1. IG1 Relay Monitor (Inside)
  2. IG2 Relay Monitor (Inside)
  3. Latch Circuit
-

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B223988E07
  1. Disconnect the I3 and I4 connectors from the power management control ECU.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I3-1 (AM22) - Body ground
    Power switch off
    11 to 14 V
    I4-7 (AM21) - Body ground
    Power switch off
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


2.CHECK HARNESS AND CONNECTOR (GROUND)
B223988E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I3-5 (E01) - Body ground
    Always
    Below 1 Ω
    I3-6 (E1) - Body ground
    Always
    Below 1 Ω
    I4-4 (E12) - Body ground
    Always
    Below 1 Ω
    I4-5 (E02) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK POWER MANAGEMENT CONTROL ECU


    B229525E14
  1. Reconnect the I3 and I4 power management control ECU connector.
    Text in Illustration 
    *a
    Component with harness connected
    (to Power Management Control ECU)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A39-2 (IG2D) - Body ground
    Power switch on (ACC) → Power switch on (IG)
    1 V or less → 9 V or higher
    I4-2 (IG1D) - Body ground
    Power switch on (ACC) → Power switch on (IG)
    1 V or less → 9 V or higher



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

END (USE SIMULATION METHOD TO CHECK) (Click here)