Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1249/49    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU receives the stop light switch assembly signal and detects the brake pedal operation status.
The skid control ECU has an open detection circuit, which stores this DTC if it detects an open in the stop light input line or ground line of the stop light circuit with the stop light switch assembly off (brake pedal not depressed).

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1249/49
231
When IG1 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or more.
  1. Wire harness or connector
  2. Stop light switch assembly
  3. Skid control ECU (Brake booster with master cylinder assembly)

WIRING DIAGRAM


C244757E04


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:

    Condition
    Illumination Condition
    Brake pedal depressed.
    ON
    Brake pedal released.
    OFF



NG
Go to step 4
OK


2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Data List on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch assembly / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch assembly display observed on the intelligent tester changes according to brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.



NG
Go to step 10
OK


3.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1249/49 is not output.
    A
    DTC C1249/49 is output (for LHD).
    B
    DTC C1249/49 is output (for RHD).
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
C173882E13
  1. Check that the STOP (7.5 A) fuse is normal.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A33-2 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


5.INSPECT STOP LIGHT SWITCH ASSEMBLY


    C239673E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    1 - 2
    Switch pin pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Stop Light Switch Assembly)



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (SWITCH INPUT)


    C244747E01
  1. Reconnect the stop light switch assembly connector.

  1. Remove the stop light control relay (STOP relay).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Stop light control relay (STOP relay) terminal 4 - Body ground
    Stop light switch assembly ON (Brake pedal depressed)
    11 to 14 V
    Stop light control relay (STOP relay) terminal 4 - Body ground
    Stop light switch assembly OFF (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block Assembly
    *2
    Stop Light Control Relay (STOP Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT STOP LIGHT CONTROL RELAY (STOP RELAY)


    C223784E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Voltage is not applied between terminals 1 and 2
    Below 1 Ω
    3 - 4
    Voltage is applied between terminals 1 and 2
    10 kΩ or higher

    Text in Illustration 
    *1
    Stop Light Control Relay (STOP Relay)



NG
REPLACE STOP LIGHT CONTROL RELAY (STOP RELAY)
OK


8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C249762E40
  1. Install the stop light control relay (STOP relay).

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-6 (STP2) - Body ground
    Stop light switch assembly ON (Brake pedal depressed)
    11 to 14 V
    A28-6 (STP2) - Body ground
    Stop light switch assembly OFF (Brake pedal released)
    Below 1.5 V
    A28-33 (STP) - Body ground
    Stop light switch assembly ON (Brake pedal depressed)
    11 to 14 V
    A28-33 (STP) - Body ground
    Stop light switch assembly OFF (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


9.RECONFIRM DTC
  1. Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1249/49 is not output.
    A
    DTC C1249/49 is output.
    B

    HINT:
    1. If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
    2. If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake booster with master cylinder assembly) (Click here for LHD or Click here for RHD).



B
INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

10.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C249762E05
  1. Turn the power switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-33 (STP) - Body ground
    Stop light switch assembly ON (Brake pedal depressed)
    11 to 14 V
    A28-33 (STP) - Body ground
    Stop light switch assembly OFF (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

    Result:

    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)