Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1249/49    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU receives the stop light switch assembly signal and detects the brake pedal operation status.
The skid control ECU has an open detection circuit, which stores this DTC if it detects an open in the stop light input line or ground line of the stop light circuit with the stop light switch assembly off (brake pedal not depressed).

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1249/49
231
When IG1 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or more.
  1. Wire harness or connector
  2. Stop light switch assembly
  3. Skid control ECU (Brake booster with master cylinder assembly)

WIRING DIAGRAM


C312696E02


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:

    Condition
    Illumination Condition
    Brake pedal depressed.
    ON
    Brake pedal released.
    OFF



NG
Go to step 4
OK


2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Data List on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch assembly / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch assembly display observed on the intelligent tester changes according to brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.



NG
Go to step 7
OK


3.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1249/49 is not output.
    A
    DTC C1249/49 is output (for LHD).
    B
    DTC C1249/49 is output (for RHD).
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Check the stop light switch assembly (Click here).

    OK:
    The stop light switch assembly is normal.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C249762E05
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-33 (STP) - Body ground
    Stop light switch assembly ON (Brake pedal depressed)
    11 to 14 V
    A28-33 (STP) - Body ground
    Stop light switch assembly OFF (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


6.RECONFIRM DTC
  1. Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1249/49 is not output.
    A
    DTC C1249/49 is output.
    B

    HINT:
    1. If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
    2. If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake booster with master cylinder assembly) (Click here for LHD or Click here for RHD).



B
INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C249762E05
  1. Turn the power switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-33 (STP) - Body ground
    Stop light switch assembly ON (Brake pedal depressed)
    11 to 14 V
    A28-33 (STP) - Body ground
    Stop light switch assembly OFF (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

    Result:

    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)