Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1231/31    Steering Angle Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The skid control ECU receives steering angle sensor signals via the CAN communication system. When a malfunction occurs in the communication line with the steering angle sensor, DTC U0126/63 (Lost Communication with Steering Angle Sensor Module) is stored.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1231/31
701
While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (sensor malfunction).
Steering angle sensor internal malfunction
↑
702
While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (internal malfunction).
↑
↑
703
While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (+B malfunction).
↑

WIRING DIAGRAM


C167662E48


INSPECTION PROCEDURE

HINT:
  1. When U0126/63 is output together with C1231/31, inspect and repair the trouble areas indicated by U0126/63 first (Click here).
  2. When a speed sensor, yaw rate and acceleration sensor (for separate type) or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) is malfunctioning, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for a speed sensor, yaw rate and acceleration sensor (for separate type) or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor, yaw rate and acceleration sensor (for separate type) and/or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) first, and then inspect and repair the steering angle sensor.

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG) again and check that no CAN communication system DTC is output (Click here).

  1. Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left check that no speed sensor and/or yaw rate and acceleration sensor DTCs are output (Click here).

    Result:

    Result
    Proceed to
    DTC C1231/31 is output.
    A
    CAN communication system DTC is output.
    B
    Speed sensor and/or yaw rate and acceleration sensor DTC is output.
    C
    DTC C1231/31 is not output.
    D

    HINT:
    1. When DTCs indicating CAN communication system malfunctions are output, repair the CAN communication system before repairing each corresponding sensor.
    2. If there is a malfunction in the speed sensor, yaw rate and acceleration sensor (for separate type) or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type), an abnormal value may be output although the steering angle sensor is normal.
    3. If speed sensor and the yaw rate and acceleration sensor DTCs are output simultaneously, repair the sensors and inspect the steering angle sensor.



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)

C
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

D
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C156493E61
  1. Turn the power switch off.

  1. Remove the steering wheel and the column cover.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the steering angle sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I30-4 (IG) - Body ground
    Power switch on (IG)
    11 to 14 V
    I30-5 (BAT) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)


    C156493E62
  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I30-1 (ESS) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor)

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)
OK

REPLACE STEERING ANGLE SENSOR (Click here)