SMART ENTRY AND START SYSTEM (for Entry Function) > Driver Side Door Entry Lock and Unlock Functions do not Operate |

| 1.CHECK POWER DOOR LOCK CONTROL SYSTEM |
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).
|
| ||||
| OK | |
| 2.CHECK WAVE ENVIRONMENT |
![]() |
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for driver door) and perform an entry function check (Click here).
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.3 m (0.984 ft.) |
| Result | Proceed to |
| Entry function does not operate normally. | A |
| Entry function operates normally. | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU) |
Disconnect the W1*1 or V1*2 front door outside handle assembly (for driver door) connector.
Disconnect the I86 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W1-3 (ANT2) - I86-4 (CG1B) | Always | Below 1 Ω |
| W1-6 (ANT1) - I86-5 (CLG1) | Always | Below 1 Ω |
| W1-5 (B) - I86-15 (POS1) | Always | Below 1 Ω |
| W1-2 (GND) - Body ground | Always | Below 1 Ω |
| W1-3 (ANT2) or I86-4 (CG1B) - Body ground | Always | 10 kΩ or higher |
| W1-6 (ANT1) or I86-5 (CLG1) - Body ground | Always | 10 kΩ or higher |
| W1-5 (B) or I86-15 (POS1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| V1-3 (ANT2) - I86-4 (CG1B) | Always | Below 1 Ω |
| V1-6 (ANT1) - I86-5 (CLG1) | Always | Below 1 Ω |
| V1-5 (B) - I86-15 (POS1) | Always | Below 1 Ω |
| V1-2 (GND) - Body ground | Always | Below 1 Ω |
| V1-3 (ANT2) or I86-4 (CG1B) - Body ground | Always | 10 kΩ or higher |
| V1-6 (ANT1) or I86-5 (CLG1) - Body ground | Always | 10 kΩ or higher |
| V1-5 (B) or I86-15 (POS1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA) |
![]() |
Disconnect the W1*1 or V1*2 front door outside handle assembly (for driver door) connector.
Connect the I86 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W1-5 (B) - W1-2 (GND)*1 V1-5 (B) - V1-2 (GND)*2 | Power switch off → on (IG) | 9 to 12 V → Below 2 V |
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
| W1-3 (ANT2) - W1-6 (ANT1)*1 V1-3 (ANT2) - V1-6 (ANT1)*2 | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
| *A | for LHD |
| *B | for RHD |
| *1 | Waveform |
| *a | Front view of wire harness connector (to Front Door Outside handle assembly (for driver door)) |
|
| ||||
| OK | |
| 5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) |
Temporarily replace the front door outside handle assembly (for driver door) with a new or known good one (Click here).
| NEXT | |
| 6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION) |
Check that the entry functions operate normally (Click here).
|
| ||||
| OK | ||
| ||