ENGINE ASSEMBLY > INSTALLATION |
| 1. REMOVE ENGINE STAND |
Using a chain block and engine sling device, secure the engine assembly.
Remove the engine stand from the engine.
| 2. INSTALL ENGINE WIRE |
Install the engine wire to the engine with transaxle.
| 3. INSTALL FLYWHEEL SUB-ASSEMBLY |
![]() |
Using SST, hold the crankshaft.
![]() |
Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 8 bolts.
| *1 | Adhesive |
![]() |
Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.
Check that the crankshaft turns smoothly.
| 4. INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY |
![]() |
Using SST, hold the crankshaft.
Install the transmission input damper.
![]() |
Install and uniformly tighten the 6 bolts in the sequence shown in the illustration.
| 5. INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY |
![]() |
Make sure that the knock pins are installed to the engine.
| *1 | Knock Pin |
Install the hybrid vehicle transaxle assembly to the engine with the 9 bolts.
| Bolt | Bolt Length | Torque |
| A, B | 55 mm (2.17 in.) | 64 N*m (653 kgf*cm, 47 ft.*lbf) |
| C | 65 mm (2.56 in.) | 46 N*m (469 kgf*cm, 34 ft.*lbf) |
| D | 32 mm (1.26 in.) | 44 N*m (449 kgf*cm, 32 ft.*lbf) |
| E | 38 mm (1.50 in.) | 28 N*m (286 kgf*cm, 21 ft.*lbf) |
| 6. INSTALL ENGINE MOUNTING BRACKET RH |
Install the engine mounting bracket RH with the 3 bolts.
| 7. INSTALL DRIVE SHAFT BEARING BRACKET |
Install the drive shaft bearing bracket with the 3 bolts.
| 8. TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR |
Temporarily install the front engine mounting insulator with the 3 nuts.
| 9. TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR LH |
Temporarily install the engine mounting insulator LH with the 3 nuts.
| 10. TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR RH |
Temporarily install the engine mounting insulator RH with the 3 nuts.
| 11. INSTALL FRONT FRAME ASSEMBLY |
Install the engine mounting insulator LH with the nut.
Install the engine mounting insulator RH with the nut.
Install the front engine mounting insulator with the bolt.
Fully tighten the 9 temporarily installed nuts of the engine mounting insulators to the specified torque.

| *a | Front Engine Mounting Insulator | *b | Engine Mounting Insulator RH |
| *c | Engine Mounting Insulator LH | - | - |
Install the 4 hole plugs.

| *a | Engine Mounting Insulator RH | *b | Engine Mounting Insulator LH |
| 12. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
Coat the spline of the front drive inboard joint assembly with ATF.
Coat the lip of the hybrid vehicle transaxle assembly type T oil seal with MP grease.
![]() |
Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.
![]() |
Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.
| *a | Matchmark |
| 13. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH |
Coat the spline of the front drive inboard joint assembly with ATF.
Coat the lip of the hybrid vehicle transaxle assembly type T oil seal with MP grease.
Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.
Install the front drive shaft assembly RH.
![]() |
Install the bearing bracket hole snap ring and a new bolt.
![]() |
Align the matchmarks and install the front drive shaft assembly RH to the front axle hub sub-assembly.
| *a | Matchmark |
| 14. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE |
Set the engine assembly with transaxle on an engine lifter.
![]() |
| *1 | No. 2 Motor Water Jacket Cover Assembly |
Remove the engine hangers .
Install the engine assembly to the vehicle.
![]() |
Install the frame side rail plate RH and LH with the 4 bolts and 2 nuts.
Install the front suspension member brace rear RH and LH with the 4 bolts and 2 nuts.
| 15. INSTALL FLYWHEEL HOUSING UNDER COVER |
Install the flywheel housing under cover.
| 16. INSTALL FRONT AXLE ASSEMBLY LH |
![]() |
Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.
| *a | Matchmark |
| 17. INSTALL FRONT AXLE ASSEMBLY RH |
| 18. INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
Connect the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.
| 19. INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH |
| 20. INSTALL TIE ROD ASSEMBLY LH |
![]() |
Install the lock nut and tie rod assembly LH to the steering rack end sub-assembly until the matchmarks are aligned.
| *a | Matchmark |
| 21. INSTALL TIE ROD ASSEMBLY RH |
| 22. INSTALL FRONT SPEED SENSOR LH |
Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt and clamp.
Install the front speed sensor to the steering knuckle with the bolt.
| 23. INSTALL FRONT SPEED SENSOR RH |
| 24. INSTALL FRONT STABILIZER LINK ASSEMBLY LH |
Install the front stabilizer link assembly to the front shock absorber assembly with the nut.
| 25. INSTALL FRONT STABILIZER LINK ASSEMBLY RH |
| 26. INSTALL FRONT AXLE SHAFT NUT LH |
Clean the threaded parts on the front drive shaft assembly and a new axle shaft nut using a non-residue solvent.
![]() |
Using a socket wrench (30 mm), install the front axle shaft nut.
Using a chisel and hammer, stake the front axle shaft nut.
| 27. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Align the matchmarks and install the steering intermediate shaft to the steering link assembly.
| *a | Matchmark |
Install the bolt.
| 28. INSTALL FRONT AXLE HUB NUT RH |
| 29. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the compression spring.
| Standard | 42.0 mm (1.65 in.) |
| Minimum | 40.5 mm (1.60 in.) |
Fully insert a new gasket to the exhaust manifold converter sub-assembly.
![]() |
Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold converter sub-assembly.
| *1 | Exhaust Manifold Converter Sub-assembly |
| *2 | Wooden Block |
| *3 | Gasket |
Connect the front exhaust pipe assembly to the exhaust pipe support.
Install the front exhaust pipe assembly with the 2 compression springs and 2 bolts.
![]() |
| *1 | Exhaust Manifold Converter Sub-assembly |
| *2 | Front Exhaust Pipe Assembly |
| *3 | Gasket |
| *a | Space between flanges: 8.5 mm (0.335 in.) |
| 30. INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
Remove the vinyl tape from the hose.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.
Install the O-ring to the No. 1 cooler refrigerant discharge hose.
Install the No. 1 cooler refrigerant discharge hose to the compressor with motor assembly with the bolt.
| 31. INSTALL NO. 1 COOLER REFRIGERANT SUCTION HOSE |
Remove the vinyl tape from the hose.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.
Install the O-ring to the No. 1 cooler refrigerant suction hose.
Install the No. 1 cooler refrigerant suction hose to the compressor with motor assembly with the bolt.
| 32. INSTALL ENGINE MOVING CONTROL ROD |
Temporarily install the engine moving control rod to the engine moving control rod bracket with the bolt.
| 33. INSTALL ENGINE MOVING CONTROL ROD BRACKET |
When the engine moving control rod has been replaced.
![]() |
Temporarily install the engine moving control rod bracket with the 4 bolts.
![]() |
Fully tighten the engine moving control rod bracket with the bolts except bolt A.
![]() |
Using SST, fully tighten the bolt A.
![]() |
When the engine moving control rod has been reused.
Temporarily install the engine moving control rod bracket with the 4 bolts.
Fully tighten the engine moving control rod bracket with the 4 bolts.
| 34. INSTALL EARTH WIRE |
Install the earth wire with the bolt.
| 35. INSTALL NO. 2 ENGINE MOUNTING STAY RH |
Install the No. 2 engine mounting stay RH with the 2 bolts.
| 36. CONNECT FUEL MAIN TUBE |
![]() |
Push in the fuel tube connector to the fuel pipe until the connector makes a "click" sound.
![]() |
Install the No. 1 fuel pipe clamp.
| 37. CONNECT INLET HEATER WATER HOSE |
Connect the inlet heater water hose.
| 38. CONNECT OUTLET HEATER WATER HOSE |
Connect the outlet heater water hose.
| 39. CONNECT NO. 5 INVERTER COOLING HOSE |
Connect the No. 5 inverter cooling hose to the hybrid vehicle transaxle assembly.
| 40. CONNECT NO. 1 RADIATOR HOSE |
Connect the air fuel ratio sensor wire to the No. 1 radiator hose with the hose clamp.
| 41. CONNECT NO. 2 RADIATOR HOSE |
Connect the No. 2 radiator hose.
| 42. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
Connect the transmission control cable assembly to the 2 transmission control cable brackets.
Install a new clip to the No. 1 transmission control cable bracket.
![]() |
Install the transmission control cable assembly to the No. 1 transmission control cable bracket
| *1 | No. 1 Transmission Control Cable Assembly |
| *2 | No. 1 Transmission Control Cable Bracket |
| *a | Claw A |
| *b | Claw B |
Connect the transmission control cable assembly to the control shaft lever with the nut.
| 43. INSTALL NO. 4 ENGINE WIRE |
Install the 3 wire harness clamps and connect the No. 4 engine wire to the fan shroud.
| 44. INSTALL INVERTER WITH CONVERTER ASSEMBLY |
![]() |
Temporarily install the inverter with converter assembly with the 2 bolts and nut.
Fully tighten the 2 bolts and nut in the order shown in the illustration.
| 45. CONNECT ENGINE WIRE |
![]() |
Connect the wire harness clamp.
Connect the connector to the ECM with the lock lever.
Install the earth wire with the bolt.
Connect the 4 connectors and wire harness clamp.
| 46. CONNECT NO. 1 INVERTER COOLING HOSE ASSEMBLY |
![]() |
Connect the No. 1 inverter cooling hose assembly to the inverter with converter assembly and lock the hose with the retainer.
| *1 | Retainer |
| 47. CONNECT NO. 4 INVERTER COOLING HOSE |
![]() |
Connect the No. 4 inverter cooling hose assembly to the inverter with converter assembly and lock the hose with the retainer.
| *1 | Retainer |
| 48. CONNECT NO. 3 ENGINE ROOM WIRE |
Connect the clamp.
Install the No. 3 engine room wire with the nut.
Install the relay block cover.
| 49. CONNECT LOW VOLTAGE CONNECTOR |
![]() |
Connect the 3 low voltage connectors and lock the connector with the lock lever.
| 50. REMOVE CONNECTOR COVER ASSEMBLY |
Remove the bolt and connector cover assembly.
| 51. CONNECT NO. 4 FLOOR WIRE |
Connect the No. 4 floor wire and wire harness clamp to the inverter with converter assembly.
Secure the No. 4 floor wire to the inverter with converter assembly with the bolt.
| 52. CONNECT NO. 4 ENGINE WIRE |
Connect the No. 4 engine wire to the inverter with converter assembly.
Connect the wire harness clamp.
| 53. INSTALL CONNECTOR COVER ASSEMBLY |
Install the connector cover assembly with the 2 bolts.
| 54. INSTALL NO. 3 MOTOR CABLE BRACKET |
Install the No. 3 motor cable bracket with the 2 bolts.
Connect the hose clamp.
| 55. CONNECT MOTOR CABLE |
Connect the motor cable to the inverter with converter assembly.
Connect the 3 wire harness clamps.
Using an insulated tool, install the 3 bolts and motor cable to the inverter with converter assembly.
| 56. INSTALL UPPER INVERTER COVER |
Install the upper inverter cover (motor cable side) with the 2 bolts.
| 57. CONNECT GENERATOR CABLE |
Connect the generator cable to the inverter with converter assembly.
Connect the 2 wire harness clamps.
Using an insulated tool, install the 3 bolts and generator cable to the inverter with converter assembly.
| 58. INSTALL UPPER INVERTER COVER |
Install the upper inverter cover (generator cable side) with the 2 bolts.
| 59. INSTALL NO. 4 INVERTER BRACKET |
Temporarily install the No. 4 inverter bracket with the 3 bolts.
![]() |
Tighten the 3 bolts in the order shown in the illustration.
| 60. INSTALL NO. 5 INVERTER BRACKET |
Temporarily install the No. 5 inverter bracket with the 2 bolts.
![]() |
Tighten the 2 bolts in the order shown in the illustration.
| 61. INSTALL AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Insert the projection of the air cleaner case sub-assembly to the hole of the No. 2 air cleaner bracket as shown in the illustration.
| *a | Projection |
Tighten the 2 bolts.
| 62. INSTALL AIR CLEANER FILTER ELEMENT |
| 63. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
Install the air cleaner hose with the hose clamp.
![]() |
Connect the 2 fuel vapor feed hoses.
| *1 | Retainer |
| *a | Push |
Install the air cleaner cap sub-assembly with the 2 clamps.
Connect the connector.
Connect the ventilation hose to the cylinder head cover.
Connect the mass air flow meter connector and wire harness clamp to the air cleaner cap sub-assembly.
| 64. INSTALL INLET AIR CLEANER ASSEMBLY |
Install the inlet air cleaner with the 2 bolts.
| 65. INSTALL SERVICE PLUG GRIP |
Wear insulated gloves and install the service plug grip in the order shown in the illustration.

Rotate the handle of the service plug grip 90° toward the battery and slide it in the direction shown by the arrow until a click sound is heard.
| 66. INSTALL NO. 8 HYBRID VEHICLE BATTERY SHIELD PANEL |
Install the No. 8 hybrid vehicle battery shield panel with the 2 nuts.
| 67. INSTALL LUGGAGE COMPARTMENT FRONT TRIM COVER |
Engage the 2 claws.
Engage the 8 fasteners and install the luggage compartment front trim cover.
| 68. INSTALL LUGGAGE COMPARTMENT FLOOR MAT |
Install the luggage compartment floor mat.
| 69. INSTALL BAGGAGE HOLDER NET (w/ Partition Net) |
Install the baggage holder net.
| 70. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
| 71. INSTALL LUGGAGE TRIM SERVICE HOLE COVER |
Engage the claw to connect the luggage trim service hole cover.
| 72. ADD ENGINE OIL |
| 73. ADD ENGINE COOLANT (for Engine) |
Tighten the radiator drain cock plug by hand.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
| Item | Capacity |
| Engine coolant | 7.2 liters (7.6 US qts, 6.3 lmp. qts) |
Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Put the engine in inspection mode (Click here).
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 74. ADD ENGINE COOLANT (for Inverter) |
| DTC Code | Detection Item |
| P0A01-725 | Motor Electronics Coolant Temperature Sensor Circuit Range / Performance |
| P0A01-726 | Motor Electronics Coolant Temperature Sensor Circuit Intermittent |
| P0A08-264 | DC / DC Converter Status Circuit |
| P0A78-284 | Drive Motor "A" Inverter Performance |
| P0A78-286 | Drive Motor "A" Inverter Performance |
| P0A7A-322 | Generator Inverter Performance |
| P0A7A-324 | Generator Inverter Performance |
| P0A93-346 | Inverter Cooling System Performance |
| P0A94-553 | DC / DC Converter Performance |
| P0A94-557 | DC / DC Converter Performance |
| P0AEE-276 | Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent / Erratic |
| P0AEE-277 | Motor Inverter Temperature Sensor "A" Circuit Range / Performance |
| P0BD0-314 | Generator Inverter Temperature Sensor Circuit Range / Erratic |
| P0BCD-315 | Generator Inverter Temperature Sensor Circuit Range / Performance |
| P0C3C-625 | DC / DC Converter Temperature Sensor "A" Intermittent / Erratic |
| P0C39-626 | DC / DC Converter Temperature Sensor "A" Range / Performance |
| P0C41-627 | DC / DC Converter Temperature Sensor "B" Intermittent / Erratic |
| P0C3E-628 | DC / DC Converter Temperature Sensor "B" Range / Performance |
| P0C73-776 | Motor Electronics Coolant Pump "A" Control Performance |
![]() |
Slowly pour coolant into the reserve tank until it reaches the FULL line.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.
Keep the coolant at the FULL line in the reserve tank to compensate for the drop in coolant level when the air bleeds.
When not using the intelligent tester:
Turn the power switch on (READY).[*1]
Turn the power switch off and add coolant to the FULL line because the coolant level drops as the air bleeds.[*2]
Repeat steps [*1] and [*2] until air bleeding from the cooling system is completed.
After the air is completely bled from the cooling system, tighten the reserve tank cap.
![]() |
Add coolant to the FULL line of the reserve tank.
| 75. ADD HYBRID TRANSAXLE FLUID |
| 76. CHARGE WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump or appropriate equipment.
Charge the air conditioning system with refrigerant.

| *a | Sub-cool System | *b | High Pressure |
| *c | Refrigerant Amount | *d | Standard charge amount |
| *e | Charge additional 100 g (3.5 oz.) | *f | Point where bubbles disappear |
| *g | Mean value in proper range | *h | Overcharged |
| 77. WARM UP ENGINE |
| 78. INSPECT FOR FUEL LEAK |
Check fuel pump operation.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG) and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.
Inspect for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
| 79. INSPECT FOR OIL LEAK |
| 80. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Put the engine in inspection mode (Click here).
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 81. INSPECT FOR EXHAUST GAS LEAK |
| 82. INSPECT REFRIGERANT LEAK |
After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
| *1 | Halogen Leak Detector |
| *a | Inspect for Leak |
![]() |
Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
| *1 | Halogen Leak Detector |
| *2 | Drain Hose |
If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.
Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.
| 83. INSPECT IGNITION TIMING |
Put the engine in inspection mode (Click here).
Warm up and stop the engine.
When using the intelligent tester:
Check the ignition timing.
Connect the intelligent tester to the DLC3.
Put the engine in inspection mode (Click here).
Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.
Check that the ignition timing advances immediately when the engine speed is increased.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.
Monitor IGN Advance of the Data List.
Enter the following menus: Connect the TC and TE1 / OFF.
Turn the power switch off.
Turn the intelligent tester off.
Disconnect the intelligent tester from the DLC3.
When not using the intelligent tester:
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *1 | DLC3 |
Remove the No. 1 engine cover sub-assembly.
Pull out the wire harness.
![]() |
Connect the clip of the timing light to the wire harness.
Inspect the ignition timing at idle.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Inspect the ignition timing at idle.
Confirm that the ignition timing advances when the engine rpm is increased.
Remove the timing light.
Install the No. 1 engine cover sub-assembly.
| 84. INSPECT ENGINE IDLE SPEED |
Put the engine in inspection mode (Click here).
Warm up and stop the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Put the engine in inspection mode (Click here).
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Inspect the engine idle speed.
Turn the power switch off.
Turn the intelligent tester off.
Disconnect the intelligent tester from the DLC3.
When not using the intelligent tester:
![]() |
Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.
| *1 | DLC3 |
Put the engine in inspection mode (Click here).
Inspect the engine idle speed.
Disconnect the tachometer probe from the DLC3.
| 85. INSPECT CO/HC |
Put the engine in inspection mode (Click here).
Warm up the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe while idling.
Check the CO/HC concentration while idling and when the engine is running at 2500 rpm.
Check the DTCs.
See the table below for possible causes, then inspect the applicable parts and repair them if necessary.
| CO | HC | Problem | Possible Cause |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|
| 86. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY |
Fit the 3 retainers and install the No. 1 engine cover sub-assembly.
| 87. INSTALL COOL AIR INTAKE DUCT SEAL |
Install the cool air intake duct seal with the 9 clips.
| 88. INSPECT AND ADJUST SHIFT LEVER POSITION |
| 89. INSTALL FRONT FENDER APRON SEAL LH |
| 90. INSTALL FRONT FENDER APRON SEAL RH |
| 91. INSTALL ENGINE UNDER COVER LH |
| 92. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH |
| 93. INSTALL ENGINE UNDER COVER RH |
| 94. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH |
| 95. INSTALL FRONT BUMPER ABSORBER LOWER |
| 96. INSTALL FRONT WHEEL |
| 97. CHECK ABS SPEED SENSOR SIGNAL |
| 98. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |