Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1311/11    Open in Main Relay 1 Circuit

DTC    C1312/12    Short in Main Relay 1 Circuit

for Preparation Click here


DESCRIPTION

The ABS main relay supplies power to the changeover solenoid and the linear solenoid.
The ABS main relay remains on for approximately 2 minutes after the power switch is turned off and the input of brake pedal operation signals stops, and supplies power to the system to keep it ready to operate.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1311/11
1
Either of the following is detected:
  1. When the power switch is on (READY):
    The ABS main relay contact is not turned ON (BS terminal voltage 3.5 V or more) for 0.2 seconds or more when ABS main relay ON is requested while IG1 terminal voltage is 9.5 V or more.
  2. When the power switch is off:
    The ABS main relay contact is not turned ON (BS terminal voltage 3.5 V or more) for 0.2 seconds or more when ABS main relay ON is requested.
  1. Open or short in ABS main relay circuit
  2. Skid control ECU (Brake booster with master cylinder assembly)
C1312/12
2
The ABS main relay contact is turned ON (BS terminal voltage 3.5 V or more) for 4.5 seconds or more when ABS main relay OFF is requested from the ECU.
  1. Short in ABS main relay circuit
  2. ABS main relay internal stuck
  3. Skid control ECU (Brake booster with master cylinder assembly)

WIRING DIAGRAM

Refer to DTCs C1241/41 and C1242/42 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (Click here).

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MAIN RELAY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Active Test on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ECB* Main Relay
    ABS main relay
    Relay ON/OFF
    -
    *: Electronically Controlled Brake System

  1. Select the Data List on the intelligent tester (Click here).


ABS/VSC/TRC 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ECB* Main Relay
ABS main relay / ON or OFF
ON: Relay on
OFF: Relay off
-
*: Electronically Controlled Brake System
  1. Check that the condition of the ABS main relay observed on the intelligent tester changes according to tester operation.

    Result:

    Result
    Proceed to
    ABS main relay in the Data List turns ON/OFF using the Active Test.
    A
    ABS main relay in the Data List does not change using the Active Test.
    B



B
Go to step 4
A


2.CHECK HARNESS AND CONNECTOR (BS TERMINAL)


    C249762E07
  1. Turn the power switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-15 (BS) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BS CIRCUIT)
OK


3.RECONFIRM DTC
  1. Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (IG).

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTCs C1311/11 and C1312/12 are not output.
    A
    DTCs C1311/11 and/or C1312/12 are output (for LHD).
    B
    DTCs C1311/11 and/or C1312/12 are output (for RHD).
    C



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK HARNESS AND CONNECTOR (BI TERMINAL)


    C249762E08
  1. Turn the power switch off.

  1. Check that the ABS NO. 1 (30 A) and ABS NO. 2 (7.5 A) fuses are normal.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-14 (BI) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BI CIRCUIT)
OK


5.CHECK HARNESS AND CONNECTOR (BS TERMINAL)


    C249762E07
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-15 (BS) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

    Result:

    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (BS CIRCUIT)
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)