Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > TERMINALS OF ECU

for Preparation Click here


HINT:
Check from the rear of the connector while it is connected to the components.


RADIO AND DISPLAY RECEIVER ASSEMBLY

E296380E04


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I152-1 (FR+) - I152-7 (GND1)
LG - BR
Sound signal (Front right)
Audio system playing
A waveform synchronized with sound signals is output
I152-2 (FL+) - I152-7 (GND1)
P - BR
Sound signal (Front left)
Audio system playing
A waveform synchronized with sound signals is output
I152-3 (ACC1) - I152-7 (GND1)
GR - BR
Power source (ACC)
Power switch off
Below 1 V
Power switch on (ACC)
11 to 14 V
I152-4 (+B1) - I152-7 (GND1)
L-Y - BR
Power source (+B)
Power switch off
11 to 14 V
I152-5 (FR-) - I152-7 (GND1)
L - BR
Sound signal (Front right)
Audio system playing
A waveform synchronized with sound signals is output
I152-6 (FL-) - I152-7 (GND1)
V - BR
Sound signal (Front left)
Audio system playing
A waveform synchronized with sound signals is output
I152-7 (GND1) - Body ground
BR - Body ground
Ground
Always
Below 1 V
I152-10 (ILL+) - I152-7 (GND1)
G - BR
Illumination signal
Power switch off
Light control switch in off position
Below 1 V
Power switch off
Light control switch in tail or head position
11 to 14 V
I153-1 (RR+) - I152-7 (GND1)
R - BR
Sound signal (Rear right)
Audio system playing
A waveform synchronized with sound signals is output
I153-2 (RL+) - I152-7 (GND1)
B - BR
Sound signal (Rear left)
Audio system playing
A waveform synchronized with sound signals is output
I153-3 (RR-) - I152-7 (GND1)
W - BR
Sound signal (Rear right)
Audio system playing
A waveform synchronized with sound signals is output
I153-5 (ILL-) - I152-7 (GND1)
W - BR
Illumination signal
Light control switch off
Below 1 V
Light control switch in tail or head position
Pulse generation
I153-6 (RL-) - I152-7 (GND1)
Y - BR
Sound signal (Rear left)
Audio system playing
A waveform synchronized with sound signals is output
I155-1 (IG) - I152-7 (GND1)
Y - BR
Power source (IG)
Power switch off
Below 1 V
Power switch on (ON)
11 to 14 V
I155-2 (REV) - I152-7 (GND1)
L - BR
Reverse signal
See "Check Vehicle Signal" in Operation Check (Click here)
-
I155-4 (MACC) - I152-7 (GND1)
B - BR
Microphone power supply
Power switch off
Below 1 V
Power switch on (ACC)
4 to 6 V
I155-5 (MIN+) - I152-7 (GND1)
W - BR
Microphone voice signal
See "Check Microphone" in Operation Check (Click here)
-
I155-6 (SNS2) - I152-7 (GND1)
LG - BR
Microphone connection detection signal
Always
Below 1 V
I155-7 (TX1+)*2
GR
AVC-LAN communication signal
-
-
I155-8 (TX1-)*2
G
AVC-LAN communication signal
-
-
I155-9 (CANH)
R
CAN communication signal
-
-
I155-10 (CANL)
W
CAN communication signal
-
-
I155-11 (AGND) - Body ground
Shield - Body ground
Shield ground
Always
Below 1 V
I155-15 (PKB) - I152-7 (GND1)
R - BR
Parking brake signal
See "Check Vehicle Signal" in Operation Check (Click here)
-
I155-17 (SPD) - I152-7 (GND1)
V - BR
Vehicle speed signal
See "Check Vehicle Signal" in Operation Check (Click here)
-
I155-18 (SGND) - Body ground
Shield - Body ground
Shield ground
Always
Below 1 V
I155-19 (MIN-) - I152-7 (GND1)
R - BR
Microphone voice signal
See "Check Microphone" in Operation Check (Click here)
-
I155-21 (SW1) - I155-23 (SWG)
B - P
Steering pad switch signal
No switch pushed
2.97 to 3.56 V
Up switch pushed
0.27 to 0.35 V
Down switch pushed
0.86 to 1.03 V
Volume+ switch pushed
1.51 to 1.79 V
Volume- switch pushed
2.22 to 2.66 V
I155-22 (SW2) - I155-23 (SWG)
Y - P
Steering pad switch signal
No switch pushed
2.97 to 3.56 V
MODE/HOLD switch pushed
0.27 to 0.35 V
On hook switch pushed
0.86 to 1.03 V
Off hook switch pushed
1.51 to 1.79 V
Voice switch pushed
2.22 to 2.66 V
I155-23 (SWG) - I152-7 (GND1)
P - BR
Steering pad switch ground
Always
Below 1 V
I155-24 (SW3) - I155-23 (SWG)
SB - P
Steering pad switch signal
No switch pushed
2.97 to 3.56 V
Enter switch pushed
0.27 to 0.35 V
Back switch pushed
0.86 to 1.03 V
Right switch pushed
1.51 to 1.79 V
Left switch pushed
2.22 to 2.66 V
I155-25 (ADPG) - I152-7 (GND1)
G - BR
External device connection detection signal
External device connected
Below 1 V
External device not connected
2.1 to 3 V
I155-26 (VAR+) - I155-27 (VA-)
B - W
Sound signal (Right)
External device playing (When stereo jack used)
A waveform synchronized with sound signals is output
I155-27 (VA-) - I152-7 (GND1)
W - BR
Ground
Always
Below 1 V
I155-28 (VAL+) - I155-27 (VA-)
R - W
Sound signal (Left)
External device playing (When stereo jack used)
A waveform synchronized with sound signals is output
I185-3 (CNH1)
GR
Local bus communication signal
-
-
I185-4 (CNL1)
W
Local bus communication signal
-
-
I185-11 (CA+) - I152-7 (GND1)*1
B - BR
Television camera power supply
Power switch on (ACC)
5.5 to 7.05 V
I185-12 (V+) - I152-7 (GND1)*1
W - BR
Video signal
Power switch on (IG)
Shift lever in R
Camera lens not covered, displaying an image
Pulse generation
(Refer to waveform 1)
Power switch on (IG)
Shift lever in R
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
I185-23 (CGND) - Body ground*1
Shield - Body ground
Shield ground
Always
Below 1 V
I185-24 (V-) - I152-7 (GND1)*1
R - BR
Ground
Always
Below 1 V
I156-1 (UPO)
-
Power source
-
-
I156-2 (UDO-)
-
Data signal
-
-
I156-3 (UDO+)
-
Data signal
-
-
I156-4 (UESG)
-
Ground
-
-
I156-5 (USG1)
-
Shield ground
-
-
RA-5 (ANT+) - I152-7 (GND1)
- - BR
Power source of antenna
Power switch on (ACC)
Radio switch on and FM or AM selected
11 to 14 V
  1. *1: w/ Rear View Monitor System
  2. *2: w/ Cooler Control Switch Assembly


    E171712E20
  1. Reference (Oscilloscope waveform):

    1. Waveform 1 (camera lens not covered, displaying an image)
      Item
      Content
      Measurement terminal
      I185-12 (V+) - I152-7 (GND1)
      Measurement setting
      200 mV/DIV., 50 μs./DIV.
      Condition
      Power switch on (IG), shift lever in R

      HINT:
      1. The video waveform changes according to the image sent by the rear television camera assembly.
      2. The video waveform is constantly output when the power switch is on (ACC).

    2. Waveform 2 (camera lens covered, blacking out the screen)
      Item
      Content
      Measurement terminal
      I185-12 (V+) - I152-7 (GND1)
      Measurement setting
      200 mV/DIV., 50 μs./DIV.
      Condition
      Power switch on (IG), shift lever in R

      HINT:
      1. The video waveform changes according to the image sent by the rear television camera assembly.
      2. The video waveform is constantly output when the power switch is on (ACC).

      Text in Illustration 
      *a
      Waveform 1 (camera lens not covered, displaying an image)
      *b
      Waveform 2 (camera lens covered, blacking out the screen)
      *c
      Synchronization Signal
      *d
      Video Waveform


COOLER CONTROL SWITCH ASSEMBLY (w/ Cooler Control Switch Assembly)

E228222E02


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
X1-1 (+B) - X1-16 (GND)
R - W-B
Power source (+B)
Power switch off
11 to 14 V
X1-5 (TX-)
Y
AVC-LAN communication signal
-
-
X1-6 (ACC) - X1-16 (GND)
GR - W-B
Power source (ACC)
Power switch off
Below 1 V
Power switch on (ACC)
11 to 14 V
X1-7 (IG+) - X1-16 (GND)
V - W-B
Power source (IG)
Power switch off
Below 1 V
Power switch on (IG)
11 to 14 V
X1-15 (TX+)
GR
AVC-LAN communication signal
-
-
X1-16 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 V