LIGHTING SYSTEM > Front Fog Light Circuit |

| 1.CHECK OPERATION (TAILLIGHTS) |
Check the operation of the taillights.
|
| ||||
| OK | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Active Test.
Check that the relay operates.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Front Fog Light Relay | Front fog light relay | ON/OFF | Light control switch is in tail position |
|
| ||||
| OK | ||
| ||
| 3.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY |
Using a voltmeter, check the signal reading of the engine room junction block assembly (Click here).
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND) |
Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A-1 (BATT) - Body ground | Power switch off | 11 to 14 V |
| B-1 (ALT) - Body ground | Power switch off | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1F-3 (GND1) - Body ground | Always | Below 1 Ω |
| 1G-4 (GND2) - Body ground | Always | Below 1 Ω |
| *a | Component without engine room junction block assembly (Engine Room Relay Block and Junction Block Assembly) | - | - |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY) |
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1G-2 (TAIL) - 3D-9 | Always | Below 1 Ω |
| 3D-9 - Body ground | Always | 10 kΩ or higher |
| 1F-13 (FOGS) - 3D-38 | Always | Below 1 Ω |
| 3D-38 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
Remove the instrument panel junction block assembly (Click here).
![]() |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| MB-13 (FFGO) - 3D-38 | Always | Below 1 Ω |
| 3D-38 - Body ground | Always | 10 kΩ or higher |
Connect a positive (+) lead from the auxiliary battery to terminal 3E-1*1 or 3F-1*2.
Connect a negative (-) lead from the auxiliary battery to terminal MB-14.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3D-9 - Body ground | Always | 11 to 14 V |
| *A | for LHD |
| *B | for RHD |
| *a | Component without harness connected (Instrument Panel Junction Block Assembly) |
|
| ||||
| OK | |
| 7.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY |
Replace the engine room junction block assembly with a new or a known good one (Click here).
Check that the fog lights operate normally.
|
| ||||
| OK | ||
| ||