Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Radio Broadcast cannot be Received or Poor Reception

for Preparation Click here


INSPECTION PROCEDURE

1.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
  1. Check the radio automatic station search function.

    1. Check the radio automatic station search function by activating it.

      Result:
      Result
      Proceed to
      Automatic station search function does not stop
      A
      Automatic station search function stops on a station
      B



B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
A


2.CHECK OPTIONAL COMPONENTS
  1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

    Result:
    Result
    Proceed to
    Optional components are not installed
    A
    Optional components are installed
    B

    NOTICE:
    Do not remove optional components without the permission of the customer.



B
REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)
A


3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY


    E187251
  1. Preparation for check

    1. Remove the antenna connector from the radio and display receiver assembly.

  1. Check for noise

    1. Turn the power switch on (ACC) with the radio and display receiver assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.

      OK:
      Noise can be heard from the speakers.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


4.CHECK WINDOW GLASS ANTENNA WIRE


    E111994E14
  1. Check for continuity in the window glass antenna wire.

    HINT:
    Check for continuity at the center of each antenna wire as shown in the illustration.

    NOTICE:
    When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger, as shown in the illustration.

    OK:
    There is continuity in the window glass antenna wire.

    Text in Illustration 
    *a
    Tester Probe
    *b
    Antenna Wire
    *c
    Tin Foil



NG
REPAIR WINDOW GLASS ANTENNA WIRE (Click here)
OK


5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
  1. Disconnect the radio and display receiver assembly connector.



    E188455E19
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    RA-5 (ANT+) - Body ground
    Power switch on (ACC)
    Radio switch on and FM or AM selected
    11 to 14 V

    Text in Illustration 
    *a
    Component without harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


6.REPLACE ANTENNA CORD SUB-ASSEMBLY
  1. Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received normally.



NG
Go to step 7
OK

NORMAL OPERATION 

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
  1. Disconnect the No. 2 antenna cord sub-assembly.

  1. Measure the resistance of the No. 2 antenna cord sub-assembly to check for an open circuit in the No. 2 antenna cord sub-assembly.

    Standard Resistance:
    Below 1 Ω

  1. Measure the resistance between the No. 2 antenna cord sub-assembly and body ground to check for a short circuit in the No. 2 antenna cord sub-assembly.

    Standard Resistance:
    10 kΩ or higher



NG
REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


8.REPLACE AMPLIFIER ANTENNA ASSEMBLY
  1. Replace the amplifier antenna assembly and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received normally.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

NORMAL OPERATION