SLIDING ROOF HOUSING > INSTALLATION |
| 1. INSTALL SLIDING ROOF HOUSING ASSEMBLY |
Loosen the 4 bolts from the sliding roof housing assembly.
Install the sliding roof housing assembly with the 4 bolts and 8 nuts.
Tighten the 4 bolts to the sliding roof housing assembly.
![]() |
for Clamp Type:
| *1 | Clip |
| *2 | Marking |
Insert the sliding roof drain hose.
Engage the claw to connect the sliding roof drain hose.
![]() |
for Clip Type:
| *1 | Clip |
| *2 | Marking |
| *a | Front Side |
| *b | Outside |
Expand the clip to insert the sliding roof drain hose.
Release the clip to connect the sliding roof drain hose.
| 2. INSTALL REAR NO. 2 SIDE RAIL SPACER LH |
![]() |
Engage the 2 claws to install the rear No. 2 side rail spacer LH.
| 3. INSTALL REAR NO. 2 SIDE RAIL SPACER RH |
| 4. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Temporarily install the curtain shield airbag assembly with the 2 hooks.

Install 2 new bolts in the order shown in the illustration.
Install the curtain shield airbag assembly to the body panel with 5 claws, 6 new clips and 2 new spacers in the order shown in the illustration.

| *1 | Pin | *2 | Clip |
| *3 | Curtain Shield Airbag Assembly | *4 | Body Panel |
| *5 | Spacer | - | - |
![]() |
Push in a new pin to each clip.
![]() |
Connect the curtain shield airbag connector.
| *1 | Airbag Connector |
| *2 | Airbag Connector Lock |
Push in the lock to install the curtain shield airbag connector.
| 5. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH |
| 6. INSTALL SLIDING ROOF PANEL OR REMOVABLE ROOF WEATHERSTRIP |
Install the sliding roof panel or removable roof weatherstrip as follows:
Position the joint of the weatherstrip at the rear center.
Align the alignment mark (yellow) on the weatherstrip with the middle marks at the corners of the sliding roof panel sub-assembly and install the weatherstrip.
Install the lip of the weatherstrip firmly.

| *1 | Joint | *2 | Rear |
| *3 | Alignment Mark (Yellow) | *4 | Middle Mark |
| *A | Normal | *B | Abnormal |
| *a | Pinched | *b | Exposed |
| *c | Gap (raised, wavy, etc.) | - | - |
| 7. INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY |
Using a T25 "TORX" socket wrench, temporarily install the sliding roof glass sub-assembly with the 4 screws.
Perform a level check.

Check the difference in level for "a" between the roof panel and the upper surface of the weatherstrip when the sliding roof glass is fully closed.
| Area | Measurement |
| A - A | 0 + 1.0 mm (0 + 0.0394 in.) 0 - 2.0 mm (0 - 0.0787 in.) |
| B - B | 0 + 2.0 mm (0 + 0.0787 in.) 0 - 1.0 mm (0 - 0.0394 in.) |
| C - C | 0 + 1.5 mm (0 + 0.0591 in.) 0 - 1.5 mm (0 - 0.0591 in.) |
| D - D | 0 + 1.5 mm (0 + 0.0591 in.) 0 - 1.0 mm (0 - 0.0394 in.) |
![]() |
Perform a gap check.
Check the width between the roof panel and roof glass.
| *a | Even |
![]() |
After adjusting the sliding roof glass, using a T25 "TORX" socket wrench, install the sliding roof glass sub-assembly with the 4 screws.
| 8. CHECK FOR WATER LEAK |
After adjusting the sliding roof glass sub-assembly, check for water leaks.
If there are any leaks, readjust the sliding roof glass sub-assembly.
| 9. INSTALL SLIDING ROOF SIDE GARNISH LH |
Engage the 2 claws to install the sliding roof side garnish LH.
| 10. INSTALL SLIDING ROOF SIDE GARNISH RH |
| 11. INSTALL ROOF HEADLINING ASSEMBLY |
| 12. RESET SLIDING ROOF DRIVE GEAR ASSEMBLY |
| 13. CHECK SLIDING ROOF SYSTEM |
| 14. INSPECT FOR WATER LEAK |
After adjusting the sliding roof glass sub-assembly, inspect for water leaks.
If there are any leaks, readjust the sliding roof glass sub-assembly.