Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REMOVAL

for Preparation Click here


NOTICE:
Make sure to select FACE mode before disconnecting the cable from the negative (-) auxiliary battery terminal.



1. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM
  1. Turn the power switch on (READY).

  1. Turn the A/C switch on.

  1. Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.

  1. Turn the power switch off.

  1. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.



2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


3. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    C239198
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel subassembly.



    C239185
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



4. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C243048
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C245589
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C243049
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



5. DISCONNECT HEATER OUTLET WATER HOSE


    E235506
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the heater outlet water hose.

    NOTICE:
    1. Do not apply excessive force to the heater outlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.



6. DISCONNECT HEATER INLET WATER HOSE


    E235507
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the heater inlet water hose.

    NOTICE:
    1. Do not apply excessive force to the heater inlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.



7. DISCONNECT SUCTION PIPE SUB-ASSEMBLY


    E227144
  1. Remove the bolt, and slide the hook connector.

  1. Disconnect the suction pipe sub-assembly.

  1. Remove the O-ring from the suction pipe sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



8. DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
  1. Disconnect the air conditioner tube and accessory assembly.

  1. Remove the O-ring from the air conditioner tube and accessory assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



9. REMOVE FRONT SEAT ASSEMBLY LH
(Click here)


10. REMOVE FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



11. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
(Click here)


12. REMOVE STEERING POST ASSEMBLY
(Click here)


13. REMOVE POWER MANAGEMENT CONTROL ECU


    B293079
  1. Disconnect the 4 connectors.



    B293080
  1. Remove the 2 nuts and power management control ECU.



14. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. for LHD:



      B292878
    1. Disconnect the 5 connectors.



    2. B292877
    3. Remove the bolt, 2 nuts and disconnect the instrument panel junction block assembly.



  1. for RHD:



      B287217
    1. Disconnect the 5 connectors.



    2. B281439
    3. Remove the bolt, nut and disconnect the instrument panel junction block assembly.



    4. B281440
    5. Remove the nut.

    6. Disengage the claw as shown in the illustration and remove the wiring harness clamp bracket.



    B279018
  1. Disengage the claw and disconnect the connector as shown in the illustration.



    B279020
  1. Disengage the claw and release the connector lock as shown in the illustration.



    B279022
  1. Disengage the claw and disconnect the connector as shown in the illustration.

  1. Remove the instrument panel junction block assembly.



15. REMOVE ECU INTEGRATION BOX RH


  1. for LHD:

    1. Disconnect each connector.



    2. E223728
    3. Remove the bolt, 2 nuts and ECU integration box RH.



  1. for RHD:

    1. Disconnect each connector.



    2. E227952
    3. Remove the bolt, 2 nuts and ECU integration box RH.



16. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Disconnect each connector.



  1. for LHD:



      E226869
    1. Remove the 2 screws.

    2. Disengage the 2 guides and remove the air conditioning amplifier assembly.



  1. for RHD:



      E228914
    1. Remove the 2 screws.

    2. Disengage the 2 guides and remove the air conditioning amplifier assembly.



17. REMOVE WINDSHIELD WIPER RELAY ASSEMBLY


    E227783
  1. Disconnect the connector.

  1. Remove the nut and windshield wiper relay assembly.



18. REMOVE FLOOR CARPET HOOK


    E227413E01
  1. Disengage the 6 guides.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



    E227415E01
  1. Disengage the 6 claws and remove the 6 floor carpet hooks.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



19. DISCONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    E227149
  1. Remove the screw.



    E227150
  1. Disengage the guide to disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.



20. REMOVE REAR NO. 4 AIR DUCT


    E227154
  1. Disengage the guide.

  1. Turn back the floor carpet as shown in the illustration.



    E227157
  1. Disengage the 4 claws to remove the rear No. 4 air duct.



21. REMOVE FLOOR CARPET BRACKET LH


    E227160
  1. Remove the 2 clips.

  1. Disengage the 2 guides to remove the floor carpet bracket LH.



22. REMOVE REAR NO. 3 AIR DUCT


    E227161
  1. Disengage the 2 claws to remove the rear No. 3 air duct.



23. REMOVE REAR NO. 2 AIR DUCT


    E227155
  1. Disengage the guide.

  1. Turn back the floor carpet as shown in the illustration.



    E227156
  1. Disengage the 4 claws to remove the rear No. 2 air duct.



24. REMOVE FLOOR CARPET BRACKET RH


    E227159
  1. Remove the 2 clips.

  1. Disengage the 2 guides to remove the floor carpet bracket RH.



25. REMOVE REAR NO. 1 AIR DUCT


    E227162
  1. Disengage the 2 claws to remove the rear No. 1 air duct.



26. REMOVE NO. 1 CONSOLE BOX MOUNTING BRACKET


    C240460
  1. Remove the screw and No. 1 console box mounting bracket from the lower shift lever assembly.



27. REMOVE NO. 1 CONSOLE BOX DUCT


    E235216
  1. Remove the clip and the No. 1 console box duct.



28. REMOVE INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY


    E234877E01
  1. Disconnect each connector.
    Text in Illustration 
    *1
    Earth Wire

  1. Disengage each clamp.

  1. Disconnect the connector.



    E227167
  1. Disengage the clamp.

  1. Remove the bolt and 2 nuts.

  1. Remove the screw and the instrument panel to cowl brace sub-assembly.



29. REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


    E234879E01
  1. Disconnect the connector.
    Text in Illustration 
    *1
    Earth Wire

  1. Disengage each clamp.

  1. Remove the bolt and disconnect the earth wire.



    E227165
  1. Remove the bolt and 2 nuts.

  1. Remove the screw and the No. 2 instrument panel brace sub-assembly.



30. REMOVE INSTRUMENT PANEL SAFETY PAD CAP


    E227183E01
  1. Put protective tape around the 5 instrument panel safety pad caps.
    Text in Illustration 
    *A
    for Driver Side
    *B
    for Passenger Side
    *1
    Protective Tape

  1. Using a screwdriver, remove the 5 instrument panel safety pad caps.



31. REMOVE FRONT LOWER PANEL PACKING


    E227177
  1. Remove the 2 front lower panel packings as shown in the illustration.



32. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT

NOTICE:
  1. Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit to break.
  2. When disassembling the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



  1. for RHD:



      E230511
    1. Remove the bolt.

    2. Disconnect the connector.



    E227851
  1. Disengage 3 claws to open the 3 clamps.



    E234665E01
  1. Disconnect the center airbag sensor connectors from the center airbag sensor assembly as shown in the illustration.
    Text in Illustration 
    *1
    Center Airbag Sensor Connector

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  1. Disconnect the 3 connectors.

  1. Disengage the 3 clamps.



  1. for LHD:

    1. Move the shift lever to N.



    2. C239451
    3. Disconnect the end of the transmission control cable assembly from the lower shift lever assembly.



    4. C239453
    5. Remove the 4 bolts and lower shift lever assembly.



    6. C239454
    7. Remove the 4 bolts and shift lever support.



    8. E235157
    9. Remove the bolt.

    10. Disconnect the connector.



  1. Using a screwdriver, disengage the 2 claws to unlock the retainer as shown in the illustration.


    E227173E01


    Text in Illustration 
    *1
    Retainer
    *2
    Protective Tape



  1. Disengage the claw and disconnect the airbag connector as shown in the illustration.


    E227175



  1. Disengage each clamp.


    E238905E01


    Text in Illustration 
    *1
    Earth Wire
    -
    -

  1. Remove the 2 bolts and disconnect the 2 earth wires.



    E234885
  1. Disconnect the connector.

  1. Disengage each clamp.



  1. Remove the bolt and disconnect the earth wire.


    E234886E01


    Text in Illustration 
    *1
    Earth Wire
    *2
    Connector Holder

  1. Remove the 2 nuts and disconnect the connector holder.

  1. Disconnect the connector.

  1. Disengage each clamp.



    E227179
  1. Remove the 2 bolts.



  1. Remove the 5 bolts and nut as shown in the illustration.


    E234636E01


    Text in Illustration 
    *1
    Movable Collar
    *2
    Body
    *3
    Instrument Panel Reinforcement
    -
    -
    *a
    Step 1
    *b
    Step 2
    *c
    Step 3
    *d
    Step 4

  1. Remove the instrument panel reinforcement assembly with air conditioning unit with the nut.

  1. Disconnect the cooler drain hose.

  1. Remove the bolt.



  1. Disengage the 3 guides and remove the instrument panel reinforcement with air conditioning unit as shown in the illustration.


    E234637



33. REMOVE AIR CONDITIONING UNIT ASSEMBLY


  1. Remove the 3 bolts and the air conditioning unit assembly from the instrument panel reinforcement assembly.


    E235219