Home › Engine / Hybrid System › 2AR-FXE FUEL › FUEL TANK

FUEL TANK > REMOVAL

for Preparation Click here



1. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
(Click here)


2. DRAIN FUEL


3. REMOVE CENTER EXHAUST PIPE ASSEMBLY
(Click here)


4. REMOVE NO. 1 FLOOR UNDER COVER


    C310498
  1. Remove the screw.
    Text in Illustration 
    V100135
    Nut (attached to under cover)
    V100136
    Screw

  1. Disengage the 5 nuts and 2 clips, and remove the No. 1 floor under cover.

    HINT:
    Rotate the clips to disengage them. The 5 nuts and 2 clips will remain attached to the No. 1 floor under cover.



5. REMOVE NO. 2 FLOOR UNDER COVER


    C310499
  1. Remove the screw and 2 clips.
    Text in Illustration 
    V100135
    Nut (attached to under cover)
    V100136
    Screw

  1. Disengage the 6 nuts and remove the No. 2 floor under cover.

    HINT:
    The 6 nuts will remain attached to the No. 2 floor under cover.



6. DISCONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY


    A259307
  1. Remove the bolt and nut of the No. 2 parking brake cable assembly.



7. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    A259308
  1. Remove the bolt and nut of the No. 3 parking brake cable assembly.



8. REMOVE REAR NO. 1 STABILIZER BAR BRACKET


    A255957
  1. Remove the 4 bolts and 2 rear No. 1 stabilizer bar brackets.



9. REMOVE LOWER CENTER FUEL TANK PROTECTOR


    A259309
  1. Remove the 4 bolts and lower center fuel tank protector.



10. DISCONNECT FUEL PUMP TUBE SUB-ASSEMBLY


    A254979E02
  1. Pinch the tube connector and then pull out the fuel pump tube sub-assembly.
    Text in Illustration 
    *1
    Retainer
    *2
    Fuel Pipe
    *3
    Fuel Tube Connector
    *4
    O-ring
    *5
    Fuel Pump Tube
    V100135
    Pinch
    V100136
    Pull Out

    NOTICE:
    1. Check that there are no scratches or foreign matter around the connected part of the fuel tube connector and fuel pipe before performing this work.
    2. Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.
    3. Only disconnect the fuel tube connector by hand.
    4. Do not forcibly bend, twist or turn the fuel pump tube.
    5. Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube connector.
    6. If the fuel tube connector and fuel pipe are stuck, push and pull to release them.



11. REMOVE FUEL TANK ASSEMBLY


    A137480
  1. Loosen the clip, then disconnect the fuel emission hose from the charcoal canister.



    A255934
  1. Support the fuel tank using an engine lifter.

    HINT:
    Using a height adjustable attachment and plate lift attachment, place the fuel tank assembly horizontally.



    A255935
  1. Remove the 2 bolts of the fuel tank bands.

  1. Slightly lower the engine lifter.



    A254980
  1. Loosen the hose clamp bolt and disconnect the fuel tank to filler pipe hose.



    A255933
  1. Loosen the hose clamp bolt and disconnect the breather tube fuel hose.

  1. Lower the engine lifter to remove the fuel tank.

    NOTICE:
    1. Slowly operate the engine lifter to lower the fuel tank.
    2. Do not drop the fuel tank.
    3. When removing the fuel tank, tilt it slightly to prevent it from interfering with the suspension arm or other surrounding parts.



    A079478
  1. Remove the 2 pins and 2 fuel tank bands as shown in the illustration.



    A136004
  1. Remove the 4 clip nuts.



12. REMOVE NO. 1 FUEL TANK CUSHION


    A259310
  1. Remove the 7 No. 1 fuel tank cushions.



13. REMOVE NO. 2 FUEL TANK PROTECTOR


    A255937E01
  1. Disengage the 2 claws, and remove the No. 2 fuel tank protector by sliding it as shown in the illustration.



14. REMOVE NO. 3 FUEL TANK PROTECTOR


    A255936E01
  1. Disengage the 2 claws, and remove the No. 3 fuel tank protector by sliding it as shown in the illustration.



15. REMOVE FUEL CUT OFF WITH TUBE VALVE ASSEMBLY


    A060493E02
  1. Insert a clip remover between the fuel cut off valve and the gasket and remove the cut off valve by gradually pushing it upward.
    Text in Illustration 
    *1
    Fuel Cut Off Valve
    *2
    Gasket

    NOTICE:
    1. Work carefully to maintain the sealing integrity of the valve as it is made from resin and easy to be damaged if forcibly removing and installing it.
    2. Be sure to install a new fuel cut off valve and gasket.

  1. Separate the 2 No. 4 fuel tube clamps.

  1. Remove the 2 fuel tank breather tube gaskets.

  1. Loosen the clip, then disconnect the fuel emission hose from the fuel cut off with tube valve assembly.



16. REMOVE FUEL PUMP TUBE SUB-ASSEMBLY


    A255959
  1. Disconnect the fuel main tube support, fuel tube clamp and remove the fuel pump tube sub-assembly.



17. REMOVE FUEL MAIN TUBE SUPPORT


    A079481
  1. Remove the bolt and fuel main tube support.



18. REMOVE NO. 4 FUEL TUBE CLAMP


    A136011
  1. Remove the 3 No. 4 fuel tube clamps.