Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY

FRONT DRIVE SHAFT ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP


  1. for One Touch Type:



      C132202E07
    1. Using a screwdriver, remove the front No. 2 axle inboard joint boot clamp.
      Text in Illustration 
      *A
      for One Touch Type
      *B
      for Claw Engagement Type

  1. for Claw Engagement Type:

    1. Using needle-nose pliers, remove the front No. 2 axle inboard joint boot clamp.
      Text in Illustration 
      *a
      claws



2. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP

HINT:
Perform the same procedure as for the front No. 2 axle inboard joint boot clamp.



3. SEPARATE FRONT AXLE INBOARD JOINT BOOT
  1. Separate the front axle inboard joint boot from the front drive inboard joint assembly.



4. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY
  1. Remove the old grease from the front drive inboard joint assembly.



    F045461E24
  1. Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Do not use a punch for the marks.

  1. Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.

  1. Hold the drive shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    F045046
  1. Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.



    C141145E12
  1. Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Do not use a punch for the marks.

  1. Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

    NOTICE:
    1. Do not tap the rollers.
    2. Do not drop the tripod joint.



5. REMOVE FRONT AXLE INBOARD JOINT BOOT
  1. Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.



6. REMOVE FRONT DRIVE SHAFT DAMPER (w/ 1 Clamp)


  1. for One Touch Type:



      C135385E09
    1. Using a screwdriver, remove the front drive shaft damper clamp.
      Text in Illustration 
      *A
      for One Touch Type
      *B
      for Claw Engagement Type

  1. for Claw Engagement Type:

    1. Using needle-nose pliers, remove the front drive shaft damper clamp.
      Text in Illustration 
      *a
      claws

  1. Remove the front drive shaft damper.



7. REMOVE FRONT DRIVE SHAFT DAMPER (w/ 2 Clamps)


    C205160E03
  1. Using needle-nose pliers, remove the 2 front drive shaft damper clamps.
    Text in Illustration 
    *a
    claws

  1. Remove the front drive shaft damper.



8. REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP


    C063445
  1. Using a screwdriver, remove the front No. 2 axle outboard joint boot clamp.



9. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

HINT:
Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.



10. REMOVE FRONT AXLE OUTBOARD JOINT BOOT
  1. Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.

  1. Remove the grease from the outboard joint.



11. REMOVE FRONT DRIVE SHAFT DUST COVER LH


    F040647E07
  1. Using SST and a press, remove the front drive shaft dust cover LH.

    SST
    09950-00020  

    NOTICE:
    1. Be careful not to drop the front drive inboard joint assembly.
    2. Do not overtighten SST.



12. REMOVE FRONT DRIVE SHAFT DUST COVER RH


    C067101
  1. Using a press, remove the front drive shaft dust cover RH.

    NOTICE:
    Be careful not to drop the front drive inboard joint assembly.



13. REMOVE FRONT DRIVE SHAFT DUST COVER (for RH Side)


    F040208E03
  1. Using SST and a press, remove the front drive shaft dust cover.

    SST
    09950-00020  

    NOTICE:
    1. Be careful not to drop the front drive inboard joint assembly.
    2. Do not overtighten SST.



14. REMOVE FRONT DRIVE SHAFT BEARING (for RH Side)


    C092033
  1. Using a snap ring expander, remove the drive shaft hole snap ring.



    F040210E04
  1. Using SST and a press, remove the front drive shaft bearing.

    SST
    09527-10011  

    NOTICE:
    Be careful not to drop the front drive inboard joint assembly.