DTC C1380/64 Stop Light Control Relay Malfunction |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| C1380/64 | 761 | When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STP0) is ON, a signal is not input to the STP2 terminal for 2 seconds or more. |
|
| ↑ | 762 | When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STP0) is OFF, the signal at the STP terminal is different from the input signal at the STP2 for 5 seconds or more. | ↑ |
| 1.CHECK STOP LIGHT OPERATION |
Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.
| Condition | Illumination Condition |
| Brake pedal depressed. | ON |
| Brake pedal released. | OFF |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Select the Data List on the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light SW | Stop light switch assembly / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
Check that the stop light switch assembly condition observed on the intelligent tester changes according to brake pedal operation.
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT CONTROL RELAY (STOP RELAY)) |
Select the Active Test on the intelligent tester (Click here).
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Stop Light Relay | Stop light control relay (STOP relay) | Relay ON/OFF | Stop lights come on |
Perform the Active Test of the stop light control relay (STOP relay) using the intelligent tester.
Select the Data List on the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light Relay Output | Stop light control relay (STOP relay) output / ON or OFF | ON: Relay output on OFF: Relay output off | - |
Check for stop light control relay (STOP relay) operation using the Data List and stop light operation by performing an Active Test.
| Result | Proceed to |
| Data List content and stop light operation are normal. | A |
| Data List content and stop light operation are abnormal or Data List content is normal but stop lights do not turn on or off. | B |
|
| ||||
| A | |
| 4.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL) |
![]() |
Turn the power switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A28-6 (STP2) - Body ground | Stop light switch assembly ON (Brake pedal depressed) | 11 to 14 V |
| A28-6 (STP2) - Body ground | Stop light switch assembly OFF (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
|
| ||||
| OK | |
| 5.RECONFIRM DTC |
Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Clear the DTCs (Click here).
Turn the power switch on (READY).
Perform a road test.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1380/64 is not output. | A |
| DTC C1380/64 is output (for LHD). | B |
| DTC C1380/64 is output (for RHD). | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL) |
![]() |
Turn the power switch off.
Remove the stop light control relay (STOP relay).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Stop light control relay (STOP relay) terminal 5 - Body ground | Always | 11 to 14 V |
| Stop light control relay (STOP relay) terminal 2 - Body ground | Power switch on (IG) | 11 to 14 V |
| *1 | No. 2 Engine Room Relay Block Assembly |
| *2 | Stop Light Control Relay (STOP Relay) |
|
| ||||
| OK | |
| 7.INSPECT STOP LIGHT CONTROL RELAY (STOP RELAY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 4 | Voltage is not applied between terminals 1 and 2 | Below 1 Ω |
| 3 - 5 | Voltage is not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 4 | Voltage is applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Voltage is applied between terminals 1 and 2 | Below 1 Ω |
| *1 | Stop Light Control Relay (STOP Relay) |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (STP0 TERMINAL) |
![]() |
Install the stop light control relay (STOP relay).
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A28-3 (STP0) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
| Result | Proceed to |
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 9.CHECK HARNESS AND CONNECTOR (STP TERMINAL) |
![]() |
Turn the power switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A28-33 (STP) - Body ground | Stop light switch assembly ON (Brake pedal depressed) | 11 to 14 V |
| A28-33 (STP) - Body ground | Stop light switch assembly OFF (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
| Result | Proceed to |
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||