Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1380/64    Stop Light Control Relay Malfunction

for Preparation Click here


DESCRIPTION

Upon receiving the hill-start assist control operating signal from the skid control ECU, the relay contact turns on and the stop lights come on.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1380/64
761
When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STP0) is ON, a signal is not input to the STP2 terminal for 2 seconds or more.
  1. Stop light switch assembly circuit
  2. Stop light control relay (STOP relay)
  3. Stop light control relay (STOP relay) circuit
  4. Skid control ECU (Brake booster with master cylinder assembly)
↑
762
When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STP0) is OFF, the signal at the STP terminal is different from the input signal at the STP2 for 5 seconds or more.
↑

WIRING DIAGRAM

Refer to DTC C1249/49 .

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (Click here).

HINT:
When C1249/49 is output together with C1380/64, inspect and repair the trouble areas indicated by C1249/49 first (Click here).

1.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

    OK:

    Condition
    Illumination Condition
    Brake pedal depressed.
    ON
    Brake pedal released.
    OFF



NG
INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Data List on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch assembly / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch assembly condition observed on the intelligent tester changes according to brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.



NG
Go to step 9
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT CONTROL RELAY (STOP RELAY))
  1. Select the Active Test on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Stop Light Relay
    Stop light control relay (STOP relay)
    Relay ON/OFF
    Stop lights come on

  1. Perform the Active Test of the stop light control relay (STOP relay) using the intelligent tester.

  1. Select the Data List on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Relay Output
    Stop light control relay (STOP relay) output / ON or OFF
    ON: Relay output on
    OFF: Relay output off
    -

  1. Check for stop light control relay (STOP relay) operation using the Data List and stop light operation by performing an Active Test.

    Result:

    Result
    Proceed to
    Data List content and stop light operation are normal.
    A
    Data List content and stop light operation are abnormal or Data List content is normal but stop lights do not turn on or off.
    B



B
Go to step 6
A


4.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)


    C249762E04
  1. Turn the power switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-6 (STP2) - Body ground
    Stop light switch assembly ON (Brake pedal depressed)
    11 to 14 V
    A28-6 (STP2) - Body ground
    Stop light switch assembly OFF (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)
OK


5.RECONFIRM DTC
  1. Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Perform a road test.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1380/64 is not output.
    A
    DTC C1380/64 is output (for LHD).
    B
    DTC C1380/64 is output (for RHD).
    C



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C244747E01
  1. Turn the power switch off.

  1. Remove the stop light control relay (STOP relay).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Stop light control relay (STOP relay) terminal 5 - Body ground
    Always
    11 to 14 V
    Stop light control relay (STOP relay) terminal 2 - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block Assembly
    *2
    Stop Light Control Relay (STOP Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


7.INSPECT STOP LIGHT CONTROL RELAY (STOP RELAY)


    C223784E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Voltage is not applied between terminals 1 and 2
    Below 1 Ω
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 4
    Voltage is applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is applied between terminals 1 and 2
    Below 1 Ω

    Text in Illustration 
    *1
    Stop Light Control Relay (STOP Relay)



NG
REPLACE STOP LIGHT CONTROL RELAY (STOP RELAY)
OK


8.CHECK HARNESS AND CONNECTOR (STP0 TERMINAL)


    C249762E09
  1. Install the stop light control relay (STOP relay).

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-3 (STP0) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

    Result:

    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP0 CIRCUIT)
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)  

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C249762E05
  1. Turn the power switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-33 (STP) - Body ground
    Stop light switch assembly ON (Brake pedal depressed)
    11 to 14 V
    A28-33 (STP) - Body ground
    Stop light switch assembly OFF (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

    Result:

    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)