Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1234/34    Yaw Rate Sensor Malfunction

DTC    C1243/43    Acceleration Sensor Stuck Malfunction

DTC    C1244/44    Open or Short in Acceleration Sensor Circuit

DTC    C1245/45    Acceleration Sensor Output Malfunction

DTC    C1279/79    Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)

DTC    C1381/97    Acceleration Sensor Power Supply Voltage Malfunction

for Preparation Click here


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor (for separate type) or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) via the CAN communication system.
The yaw rate sensor has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2) (for separate type).
The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2) (for built-in type).
If there are any problems in the bus lines between the yaw rate and acceleration sensor (for separate type) or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) and the CAN communication system, DTCs U0123/62 (Lost Communication with Yaw Rate Sensor Module) and U0124/95 (Lost Communication with Lateral Acceleration Sensor Module) are stored.
These DTCs are also output when calibration has not been completed.
DTC C1279/79 will be cleared when the yaw rate and acceleration sensor (for separate type) or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) sends a yaw rate and/or acceleration signal or when Test Mode ends. DTC C1279/79 is output only in Test Mode.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1234/34
711
While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 1 (GL1) malfunction).
  1. Yaw rate and acceleration sensor internal malfunction (for separate type)
  2. Yaw rate and acceleration sensor (Airbag sensor assembly) internal malfunction (for built-in type)
↑
712
While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 2 (GL2) malfunction).
↑
↑
713
While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Zero point calibration malfunction).
↑
↑
714
While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Two-value comparison malfunction).
↑
C1243/43
561
An acceleration sensor malfunction occurs 16 times or more when the vehicle speed drops from above 30 km/h (19 mph) to 0 km/h (0 mph).
  1. Yaw rate and acceleration sensor internal stuck malfunction (for separate type)
  2. Yaw rate and acceleration sensor (Airbag sensor assembly) internal stuck malfunction (for built-in type)
↑
562
563
564
A stuck acceleration sensor value is determined.
↑
C1244/44
571
Either of the following is detected:
  1. Difference between GL1 and GL2 does not become less than 0.4 G for 60 seconds or more after reaching 0.6 G when the vehicle is stopped.
  2. A malfunction signal from the acceleration sensor is received.
  1. Yaw rate and acceleration sensor installed improperly (for separate type)
  2. Yaw rate and acceleration sensor (Airbag sensor assembly) installed improperly (for built-in type)
  3. Yaw rate and acceleration sensor (for separate type)
  4. Yaw rate and acceleration sensor (Airbag sensor assembly) (for built-in type)
C1245/45
581
Difference between longitudinal G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
  1. Yaw rate and acceleration sensor installed improperly (for separate type)
  2. Yaw rate and acceleration sensor (Airbag sensor assembly) installed improperly (for built-in type)
  3. Yaw rate and acceleration sensor (for separate type)
  4. Yaw rate and acceleration sensor (Airbag sensor assembly) (for built-in type)
C1381/97
601
While yaw rate and acceleration sensor communication is enabled, a supply voltage malfunction signal is received from the sensor for 10 seconds.
  1. Yaw rate and acceleration sensor supply voltage shut down (for separate type)
  2. Yaw rate and acceleration sensor (Airbag sensor assembly) supply voltage shut down (for built-in type)
  3. Yaw rate and acceleration sensor (for separate type)
  4. Yaw rate and acceleration sensor (Airbag sensor assembly) (for built-in type)
  5. Skid control ECU (Brake booster with master cylinder assembly)
C1279/79
-
Detected only during Test Mode.
  1. Sensor installation
  2. Yaw rate and acceleration sensor (for separate type)
  3. Yaw rate and acceleration sensor (Airbag sensor assembly) (for built-in type)

WIRING DIAGRAM


for Separate Type

C249129E04


for Built-in Type

C246787E05


INSPECTION PROCEDURE

NOTICE:
When replacing the yaw rate and acceleration sensor (for separate type) or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type), perform zero point calibration (Click here).

HINT:
When U0123/62 and/or U0124/95 is output together with C1234/34, C1243/43, C1244/44, C1245/45, and/or C1381/97, inspect and repair the trouble areas indicated by U0123/62 and/or U0124/95 first (Click here).

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (READY).

  1. Drive the vehicle at a speed of 30 km/h (19 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.

  1. Turn the power switch on (IG) again and check that no CAN communication system DTC is output (Click here).

  1. Check if DTC C1210/36 (Zero Point Calibration of Yaw Rate Sensor Undone) or C1336/98 (Zero Point Calibration of Acceleration Sensor Undone) is output (Click here).

    Result:

    Result
    Proceed to
    DTCs (C1210/36, C1336/98 and CAN communication system DTC) are not output (for separate type yaw rate sensor).
    A
    DTCs (C1210/36, C1336/98 and CAN communication system DTC) are not output (for built-in type yaw rate sensor).
    B
    CAN communication system DTC is output.
    C
    DTCs C1210/36 and/or C1336/98 are output.
    D



B
Go to step 5

C
INSPECT CAN COMMUNICATION SYSTEM (Click here)

D
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


2.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
  1. Turn the power switch off.

  1. Check that the yaw rate and acceleration sensor has been installed properly (Click here).

    OK:
    The sensor is tightened to the specified torque.
    The sensor is not tilted.



NG
INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (IG TERMINAL)


    C235291E05
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the yaw rate and acceleration sensor connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I174-4 (IG) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Acceleration Sensor)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)
OK


4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)


    C235291E06
  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I174-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Acceleration Sensor)

    NOTICE:
    Check the yaw rate and acceleration sensor signal after replacement (Click here).

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK

REPLACE YAW RATE AND ACCELERATION SENSOR (Click here)  

5.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
  1. Turn the power switch off.

  1. Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly (Click here).

    OK:
    The sensor is tightened to the specified torque.
    The sensor is not tilted.



NG
INSTALL AIRBAG SENSOR ASSEMBLY CORRECTLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)


    C239271E05
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the yaw rate and acceleration sensor (airbag sensor assembly) connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I47-21 (IG2) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 CIRCUIT)
OK


7.CHECK HARNESS AND CONNECTOR (E TERMINAL)


    C239271E06
  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I47-25 (E1) - Body ground
    Always
    Below 1 Ω
    I47-26 (E2) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))

    NOTICE:
    Check the yaw rate and acceleration sensor signal after replacement (Click here).

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (E CIRCUIT)
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)