Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM

STEERING LOCK SYSTEM > Unable to Lock Steering Wheel

for Preparation Click here


DESCRIPTION

The steering lock actuator activates the steering lock motor and moves the lock bar into the steering column to lock the steering.
When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little in the same manner as is done for a vehicle with a mechanical key to change the position of the lock hole.

Related Data List and Active Test Items 
Problem Symptom
Data List Item
Active Test Item
Unable to lock steering wheel
Entry&Start
  1. All items (Click here)
Main Body
  1. FR Door Courtesy
  2. FL Door Courtesy
-

WIRING DIAGRAM


C245393E01


INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.
  2. Perform either of the following operations to lock/unlock the steering:
    1. To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG) with the shift lever in P.
    2. To lock the steering, turn the power switch off with the shift lever in P, and then open a door.
  3. Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (Click here).
  4. The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
  5. When replacing the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly), registration must be performed (refer to Service Bulletin).
  6. After performing repairs, confirm that the problem does not occur.
  7. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  8. When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected (Click here).

1.CHECK DTC (ALL)
  1. Using the intelligent tester, confirm the output of DTCs for all systems.

    OK:
    No DTCs are output.

    NOTICE:
    1. When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.
    2. Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart (Click here).



NG
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
OK


2.READ VALUE USING INTELLIGENT TESTER (LOCK REQUEST RECEIVE)
  1. Use the Data List to check if the steering lock command is functioning properly.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Lock Request Receive
    Reception state of steering lock request signal by certification ECU (smart key ECU assembly) / OK or NG

    HINT:
    1. The reception state is maintained for 10 seconds.
    2. When 10 seconds or more elapse after receiving the signal, the item changes to "NG".

    OK: Within 10 seconds of opening any door with power switch off and shift lever in P
    NG: Except above
    If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.

    OK:
    The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the power switch from on (IG) to off and opening a door with the shift lever in P, and OK is displayed on the intelligent tester screen.



NG
Go to step 5
OK


3.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the I24 steering lock ECU connector.



    C157850E40
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I24-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Lock ECU (Steering Lock Actuator Assembly))

  1. Reconnect the I24 steering lock ECU connector.

  1. Turn the power switch off, make sure that the steering is unlocked and move the shift lever to P.



    C241547E02
  1. Check the signal waveform according to the condition(s) in the table below.
    Standard Frequency 
    Item
    Content
    Tester Connection
    I24-3 (IGE) - I24-1 (GND)
    Tool Setting
    2 V/DIV., 200 ms./DIV.
    Vehicle Condition
    Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating
    Text in Illustration 
    *a
    Component with harness connected
    (Steering Lock ECU (Steering Lock Actuator Assembly))
    *b
    Steering lock motor not operating
    *c
    Steering lock motor operating

    HINT:
    1. When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
    2. In order to take measurements when the lock motor is operating, perform either of the following operations:
      1. To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG) with the shift lever in P.
      2. To lock the steering, turn the power switch off with the shift lever in P, and then open a door.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - POWER MANAGEMENT CONTROL ECU)
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the I24 steering lock ECU connector.

  1. Disconnect the I4 power management control ECU connector.

  1. Check for deformation and corrosion of the connector case and terminals.

    OK:
    There is no deformation or corrosion of the connector case or terminals.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I24-3 (IGE) - I4-6 (SLR+)
    Always
    Below 1 Ω
    I24-3 (IGE) - Body ground
    Always
    10 kΩ or higher
    I4-6 (SLR+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEERING LOCK ACTUATOR ASSEMBLY (Click here)  

5.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY)
  1. Using the intelligent tester, check the following main body ECU Data List item by opening and closing the driver door to confirm the state of the front door courtesy light switch assembly.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Courtesy*1
    Front door courtesy light switch assembly RH / CLOSE or OPEN
    CLOSE: Front door RH closed
    OPEN: Front door RH open
    If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or a related part.
    FL Door Courtesy*2
    Front door courtesy light switch assembly LH / CLOSE or OPEN
    CLOSE: Front door LH closed
    OPEN: Front door LH open
    If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or a related part.
    *1: for RHD
    *2: for LHD

    OK:
    The Data List item changes in accordance with the opening and closing of the driver door.



NG
GO TO LIGHTING SYSTEM (FRONT DOOR COURTESY SWITCH CIRCUIT) (Click here)
OK


6.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)
  1. Use the Data List to check if L code certification is functioning properly.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    L Code Check
    Verification result between certification ECU (smart key ECU assembly) and steering lock ECU / OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When a malfunction is present:
    1. The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU is malfunctioning.
    2. The steering cannot be locked.
    3. The steering cannot be unlocked (the hybrid control system cannot be started).

    OK:
    OK is displayed on the intelligent tester.

    HINT:
    Reasons for verification failure:
    1. The steering lock ECU or certification ECU (smart key ECU assembly) is malfunctioning.
    2. There is a problem with the communication between ECUs.
    3. An ECU is replaced, but is not registered.
    4. An ECU is replaced with an ECU which has a code already stored in it.



NG
Go to step 8
OK


7.REPLACE STEERING LOCK ACTUATOR ASSEMBLY
  1. Replace the steering lock ECU (steering lock actuator assembly) with a new one (Click here).

  1. Perform registration (refer to Service Bulletin).

  1. Turn the power switch on (IG).

  1. Turn the steering wheel and check the steering condition.

    OK:
    Steering is unlocked.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END 

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly) with a new one.

  1. Perform registration (refer to Service Bulletin).

  1. Use the Data List to check if L code certification is functioning properly again.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    L Code Check
    Verification result between certification ECU (smart key ECU assembly) and steering lock ECU / OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When a malfunction is present:
    1. The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU is malfunctioning.
    2. The steering cannot be locked.
    3. The steering cannot be unlocked (the hybrid control system cannot be started).

    OK:
    OK is displayed on the intelligent tester.



NG
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (Click here)
OK

END