Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Open in CAN Main Bus Line (LHD Models)

for Preparation Click here


DESCRIPTION

There may be an open circuit in one of the V bus main lines and/or a DLC3 branch line when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher.
  1. DLC3 branch line or connector
  2. CAN main bus line or connector
  3. ECM
  4. Combination meter assembly
  5. CAN junction LH connector
  6. CAN junction RH connector
This malfunction is not related to the lines of a CAN main bus branch or to ECUs or sensors connected a CAN main bus branch.

WIRING DIAGRAM


C244445E07


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the power switch on (IG), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 11 seconds.
  6. After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
  3. Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.

1.CHECK FOR OPEN IN CAN BUS LINES (DLC3 BRANCH LINE)
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



    C210421E46
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3

    NOTICE:
    When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area (Click here).



NG
REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3
OK


2.CHECK FOR OPEN IN CAN BUS LINES (ECM - CAN J/C RH)


    C239823E06
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A25-13 (CANH) -A25-26 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
Go to step 3
OK

REPLACE ECM (Click here)  

3.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - CAN J/C LH)
  1. Reconnect the ECM connector.



    E224284E17
  1. Disconnect the combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-16 (CANH) - I18-15 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
Go to step 4
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

4.CHECK FOR OPEN IN CAN BUS LINES (CAN J/C LH)
  1. Reconnect the combination meter assembly connector.



    C251258E01
  1. Disconnect the CAN junction LH connectors (I93 and I94).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    I94-1 (CANH) - I94-2 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    Combination meter assembly
    I93-1 (CANH) - I93-2 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    CAN junction RH connector

    Wiring Color:
    Code
    Color (CANH Side)
    Color (CANL Side)
    Connected to
    I94
    R
    W
    Combination meter assembly
    I93
    B
    W
    CAN junction RH connector

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction LH Connector)
    *b
    to Combination Meter Assembly
    *c
    to CAN Junction RH Connector

    NOTICE:
    1. Before disconnecting the connectors, make a note of where they are connected.
    2. Reconnect each connector to its original position.

    Result:
    Result
    Proceed to
    OK
    A
    NG (Combination meter assembly main line)
    B
    NG (CAN junction RH connector main line)
    C



B
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN J/C LH - COMBINATION METER ASSEMBLY)

C
Go to step 5
A

REPLACE CAN JUNCTION LH CONNECTOR 

5.CHECK FOR OPEN IN CAN BUS LINES (CAN J/C RH)
  1. Reconnect the CAN junction LH connector (I93 and I94).



    C248234E01
  1. Disconnect the CAN junction RH connectors (I101 and I104).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    I104-1 (CANH) - I104-2 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    ECM
    I101-1 (CANH) - I101-2 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    CAN junction LH connector

    Wiring Color:
    Code
    Color (CANH Side)
    Color (CANL Side)
    Connected to
    I104
    P
    W
    ECM
    I101
    B
    W
    CAN junction LH connector

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN junction RH Connector)
    *b
    to CAN junction LH Connector
    *c
    to ECM

    NOTICE:
    1. Before disconnecting the connectors, make a note of where they are connected.
    2. Reconnect each connector to its original position.

    Result:
    Result
    Proceed to
    OK
    A
    NG (CAN junction LH connector main line)
    B
    NG (ECM main line)
    C



B
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN J/C LH - CAN J/C RH)

C
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN J/C RH - ECM)
A

REPLACE CAN JUNCTION RH CONNECTOR