Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM

WINDOW DEFOGGER SYSTEM > Rear Window Defogger System does not Operate

for Preparation Click here


DESCRIPTION

When the rear window defogger switch on the air conditioning panel (heater control switch board) is pressed, the operation signal is transmitted to the air conditioning amplifier assembly through a LIN communication line. When the air conditioning amplifier assembly receives the signal, it turns on the engine room junction block assembly to operate the rear window defogger.

WIRING DIAGRAM


B280953E08


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. If the auxiliary battery voltage becomes low, rear window defogger operation is canceled to prioritize supplying power to the power steering system.

1.CHECK AIR CONDITIONING SYSTEM
  1. Check the air conditioning system.

    HINT:
    Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly through the same communication line.

    OK:
    The air conditioning system operates normally.



NG
GO TO AIR CONDITIONING SYSTEM (Click here)
OK


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DEFOGGER RELAY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch to on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    Air Conditioner (Air Conditioning Amplifier Assembly) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Defogger Relay (Rear)
    Rear window defogger
    OFF or ON
    -

    OK:
    The rear window defogger system operates normally.



NG
Go to step 3
OK

REPLACE AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD) (Click here)  

3.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
  1. Using a voltmeter, check the signal reading of the engine room junction block assembly (Click here).

    OK:
    Output signal reading is normal.



NG
INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK) (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)


  1. Remove the engine room junction block assembly from the engine room relay block and junction block assembly.


    E230000E04

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A-1 (BATT) - Body ground
    Power switch off
    11 to 14 V
    B-1 (ALT) - Body ground
    Power switch off
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1F-3 (GND1) - Body ground
    Always
    Below 1 Ω
    1G-4 (GND2) - Body ground
    Always
    Below 1 Ω


Text in Illustration 
*a
Component without engine room junction block assembly
(Engine Room Relay Block and Junction Block Assembly)
-
-


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the I77 air conditioning amplifier assembly connector.

  1. Disconnect the 1F engine room junction block assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I77-38 (RDFG) - 1F-4 (DEFS)
    Always
    Below 1 Ω
    1F-4 (DEFS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
  1. Reconnect the 1F engine room junction block assembly connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I77-38 (RDFG) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY (Click here)
OK


7.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


    B274526E03
  1. Reconnect the I77 air conditioning amplifier assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I77-38 (RDFG) - I77-14 (GND)
    Power switch on (IG), rear window defogger switch off
    11 to 14 V
    I77-38 (RDFG) - I77-14 (GND)
    Power switch on (IG), rear window defogger switch on
    Below 2.2 V

    Text in Illustration 
    *a
    Component with harness connected
    (Air Conditioning Amplifier Assembly)



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - REAR WINDOW DEFOGGER WIRE)
  1. Disconnect the N29 rear window defogger wire (back window glass) auxiliary battery side connector.

  1. Disconnect the 1N engine room junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1N-1 (RDEF) - N29-1
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
  1. Reconnect the 1N engine room junction block assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N29-1 - Body ground
    Power switch on (IG), rear window defogger switch on
    11 to 14 V
    N29-1 - Body ground
    Power switch on (IG), rear window defogger switch off
    Below 1 V



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (REAR WINDOW DEFOGGER WIRE - BODY GROUND)
  1. Disconnect the P1 rear window defogger wire (back window glass) ground side connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P1-1 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE REAR WINDOW DEFOGGER WIRE (BACK WINDOW GLASS) (Click here)