Home › Engine / Hybrid System › 2AR-FXE STARTING › POWER SWITCH

POWER SWITCH > INSTALLATION

for Preparation Click here



1. INSTALL POWER SWITCH (for RHD)
  1. Engage the 2 claws to install the power switch.



2. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL (for RHD)
  1. Connect the connector.



    B287369
  1. Engage the 2 claws and 4 clips to install the upper instrument panel finish panel.



3. INSTALL INSTRUMENT SIDE PANEL RH (for RHD)


    B281766
  1. Engage the 3 guides as shown in the illustration.



    B281764
  1. Engage the 4 claws to install the instrument side panel RH as shown in the illustration.



4. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)


    B278981E01
  1. Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
    Text in Illustration 
    *1
    Alignment Mark (White)

    NOTICE:
    After installation, check that the corners fit correctly.



5. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH (for RHD)

HINT:
Use the same procedure as for the LH side .



6. INSTALL FRONT DOOR SCUFF PLATE RH (for RHD)

HINT:
Use the same procedure as for the LH side .



7. INSTALL POWER SWITCH (for LHD)
  1. Engage the 2 claws to install the power switch.



8. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)
  1. for LHD:

    1. Connect the connector.

  1. Engage the 3 clips and guide to install the lower instrument panel finish panel assembly.



9. INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for LHD)
  1. for LHD:

    1. Engage the 2 claws to connect the room temperature sensor.



    B281776
  1. Engage the clip and 3 guides as shown in the illustration.

  1. Install the front No. 2 console box insert with the 2 screws <C>.



10. INSTALL CONSOLE BOX ASSEMBLY (for LHD)
(Click here).


11. INSTALL FRONT ASH RECEPTACLE ASSEMBLY (for LHD)
  1. Connect each connector.



    B281756
  1. Engage the 2 clips.

  1. Install the front ash receptacle assembly with the 2 screws <C>.



12. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)
  1. Engage the 5 clips and 3 guides.

  1. Install the instrument panel sub-assembly with the 2 bolts <B>.



13. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for LHD)
  1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.



14. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for LHD)


    B280330
  1. Temporarily install the instrument cluster finish panel assembly as shown in the illustration.

  1. Connect each connector.

  1. for LHD:

    1. Engage the 3 claws, 7 clips and 4 guides.

  1. for RHD:

    1. Engage the 4 claws, 5 clips and 4 guides.



    B283375
  1. Engage the 4 clips and 2 guides to install the instrument cluster finish panel assembly.



15. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for LHD)


    B280325
  1. Engage the 4 clips to install the No. 1 instrument panel register assembly.



16. INSTALL INSTRUMENT SIDE PANEL LH (for LHD)


    B293646
  1. Engage the 3 guides.



    B280321
  1. Engage the 4 claws to install the instrument side panel LH as shown in the illustration.



17. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for LHD)


    B278980E01
  1. Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *1
    Alignment Mark (Yellow)

    NOTICE:
    After installation, check that the corners fit correctly.



18. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD)


    B294701
  1. Insert the 2 clips in the direction indicated by the arrows shown in the illustration to engage them.

  1. Install the cowl side trim sub-assembly LH with the clip.



19. INSTALL FRONT DOOR SCUFF PLATE LH (for LHD)
  1. Engage the 10 claws to install the front door scuff plate LH.



20. INSTALL RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for LHD)
(Click here).


21. CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


22. INSTALL LUGGAGE TRIM SERVICE HOLE COVER
  1. Engage the claw to connect the luggage trim service hole cover.