CONDENSER > INSTALLATION |
| 1. INSTALL COOLER CONDENSER ASSEMBLY |
![]() |
Insert the cooler condenser as shown in the illustration.
![]() |
Temporarily install the 2 bolts <A>.
Install the cooler condenser assembly with the 2 bolts <A> and 2 bolts<B>.
| 2. CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY |
Remove the vinyl tape from the tube and the connector part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the tube joint.
Install the O-ring to the air conditioner tube and accessory assembly.
Install the air conditioner tube and accessory assembly to the cooler condenser assembly with the bolt.
| 3. CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
Remove the attached vinyl tape from the pipe and the connecting part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.
Install the O-ring to the No. 1 cooler refrigerant discharge hose.
Install the No. 1 cooler refrigerant discharge hose to the cooler condenser assembly with the bolt.
| 4. INSTALL RADIATOR SIDE DEFLECTOR LH |
![]() |
Engage the guide and 3 claws to install the radiator side deflector LH as shown in the illustration.
| 5. INSTALL RADIATOR SIDE DEFLECTOR RH |
Engage the 3 claws to install the radiator side deflector RH.
| 6. INSTALL UPPER RADIATOR SUPPORT |
Install the 2 radiator support cushions to the radiator assembly.
Install the upper radiator support with the 5 bolts and connect the hood lock control cable clamp to the upper radiator support.
Connect the 2 connectors.
| 7. INSTALL HOOD LOCK ASSEMBLY (for LHD) |
![]() |
Apply MP grease to the sliding areas of the lock.
Connect the hood lock control cable assembly.
Install the hood lock assembly with the 2 bolts and hood lock bolt.
Connect the connector.
| 8. INSTALL HOOD LOCK ASSEMBLY (for RHD) |
![]() |
Apply MP grease to the sliding areas of the lock.
Connect the hood lock control cable assembly.
Install the hood lock assembly with the 2 bolts and hood lock bolt.
Connect the connector.
| 9. INSTALL NO. 5 INVERTER BRACKET |
Temporarily install the No. 5 inverter bracket with the 2 bolts.
![]() |
Tighten the 2 bolts in the order shown in the illustration.
| 10. INSTALL INLET AIR CLEANER ASSEMBLY |
Install the inlet air cleaner with the 2 bolts.
| 11. INSTALL FRONT BUMPER ASSEMBLY |
| 12. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
| 13. INSTALL LUGGAGE TRIM SERVICE HOLE COVER |
Engage the claw to connect the luggage trim service hole cover.
| 14. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump or appropriate equipment.
Charge the air conditioning system with refrigerant.

| *a | Sub-cool System | *b | High Pressure |
| *c | Refrigerant Amount | *d | Standard charge amount |
| *e | Charge additional 100 g (3.5 oz.) | *f | Point where bubbles disappear |
| *g | Mean value in proper range | *h | Overcharged |
| 15. WARM UP COMPRESSOR |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 16. INSPECT FOR REFRIGERANT LEAK |
After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
| *1 | Halogen Leak Detector |
| *a | Inspect for Leak |
![]() |
Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
| *1 | Halogen Leak Detector |
| *2 | Drain Hose |
If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.
Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.
| 17. ADJUST HOOD SUB-ASSEMBLY |