Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER

CONDENSER > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM
  1. Turn the power switch on (READY).

  1. Turn the A/C switch on.

  1. Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.

  1. Turn the power switch off.

  1. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.



3. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    A259067
  1. Disengage the claw to remove the luggage trim service hole cover.



4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


5. REMOVE FRONT BUMPER ASSEMBLY
(Click here)


6. REMOVE INLET AIR CLEANER ASSEMBLY


    A259747
  1. Remove the 2 bolts and inlet air cleaner assembly.



7. REMOVE HOOD LOCK ASSEMBLY (for LHD)


    B281661E01
  1. Using a screwdriver, remove the hood lock nut cap.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    B281667
  1. Disconnect the connector.



    B281671E01
  1. Remove the 2 bolts and hood lock bolt.
    Text in Illustration 
    *1
    Hood Lock Bolt



    B281672
  1. Disconnect the hood lock control cable assembly and remove the hood lock assembly.



8. REMOVE HOOD LOCK ASSEMBLY (for RHD)


    B281669E01
  1. Using a screwdriver, remove the hood lock nut cap.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    B281668
  1. Disconnect the connector.



    B281670E01
  1. Remove the 2 bolts and hood lock bolt.
    Text in Illustration 
    *1
    Hood Lock Bolt



    B281673
  1. Disconnect the hood lock control cable assembly and remove the hood lock assembly.



9. REMOVE NO. 5 INVERTER BRACKET


    A258737
  1. Remove the 2 bolts and No. 5 inverter bracket.



10. REMOVE UPPER RADIATOR SUPPORT


    A263146
  1. Disconnect the 2 connectors.



    A264073E01
  1. Disconnect the hood lock control cable clamp and remove the 5 bolts and upper radiator support.
    Text in Illustration 
    *a
    for RHD:
    *b
    for LHD:

  1. Remove the 2 radiator support cushions.



11. REMOVE RADIATOR SIDE DEFLECTOR RH


    A259977
  1. Disengage the 3 claws and remove the radiator side deflector RH.



12. REMOVE RADIATOR SIDE DEFLECTOR LH


    E230562E01
  1. Disengage the 3 claws and guide, and remove the radiator side deflector LH as shown in the illustration.



13. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE


    E230564
  1. Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the cooler condenser assembly.

  1. Remove the O-ring from the No. 1 cooler refrigerant discharge hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



14. DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY


    E230565
  1. Remove the bolt and disconnect the air conditioner tube and accessory assembly from the cooler condenser assembly.

  1. Remove the O-ring from the air conditioner tube and accessory assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



15. REMOVE COOLER CONDENSER ASSEMBLY


    E230566
  1. Remove the 4 bolts.



    E230567
  1. Pull the radiator assembly in the direction indicated by the arrow.



    E230569
  1. Remove the 2 bolts.



    E230570
  1. Remove the cooler condenser assembly as shown in the illustration.