Home › Engine / Hybrid System › 2AR-FXE INTAKE / EXHAUST › INTAKE MANIFOLD

INTAKE MANIFOLD > INSTALLATION

for Preparation Click here



1. SET INTAKE MANIFOLD
  1. Install the fuel vapor feed hose to the intake manifold.

  1. Install the vacuum hose to the intake manifold.

  1. Install the wire harness clamp bracket with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install a new gasket to the intake manifold.

  1. Set the intake manifold on the engine assembly.



2. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY


    A259323E01
  1. Install 4 new injector vibration insulators to the cylinder head.
    Text in Illustration 
    *1
    Fuel Delivery Spacer
    *a
    Fuel Delivery Pipe Side
    *b
    Cylinder Head Side

  1. Install the 2 fuel delivery spacers onto the cylinder head.

    HINT:
    Install the fuel delivery spacer so that the longer protrusion is on the cylinder head side.



    A259321
  1. Install the fuel delivery pipe sub-assembly with the 4 fuel injector assemblies and install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    1. Do not drop the fuel injectors when installing the fuel delivery pipe sub-assembly.
    2. Check that the fuel injector assemblies rotate smoothly after installing the fuel delivery pipe sub-assembly.

  1. Connect the 4 fuel injector connectors.



3. CONNECT FUEL TUBE SUB-ASSEMBLY


    A259317
  1. Push the tube connector onto the pipe until the tube connector makes a "click" sound.

    NOTICE:
    1. Before connecting the fuel tube connector and fuel pipe, check that there is no damage or foreign matter on the connecting part of the fuel pipe.
    2. After connecting the fuel tube connector and fuel pipe, check that they are securely connected by trying to pull them apart.

  1. Install the No. 1 fuel pipe clamp.



4. INSTALL INTAKE MANIFOLD
  1. Temporarily install the intake manifold with the 6 bolts.



    A257344E01
  1. Tighten the 6 bolts in the order shown in the illustration.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Connect the 6 wire harness clamps.

  1. Connect the heated oxygen sensor connector.

  1. Connect the No. 2 ventilation hose.



5. INSTALL MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Install the manifold absolute pressure sensor with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the vacuum hose and connector.



6. INSTALL INTAKE FLANGE
  1. Install a new gasket to the intake manifold.

  1. Install the intake flange with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



7. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
  1. Install the front outer cowl top panel sub-assembly with the 10 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.



8. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
  1. Install the front outer cowl top panel sub-assembly with the 10 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.



9. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


10. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY
(Click here)


11. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


12. INSTALL LUGGAGE TRIM SERVICE HOLE COVER
  1. Engage the claw to connect the luggage trim service hole cover.



13. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG) and turn the intelligent tester on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Inspect for fuel leaks.

    1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the power switch off.

  1. Disconnect the intelligent tester from the DLC3.