Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function)

SMART ENTRY AND START SYSTEM (for Entry Function) > Driver Side Door Entry Unlock Function does not Operate

for Preparation Click here


DESCRIPTION

If the entry unlock function does not operate for the driver door only, but the entry lock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the touch sensor (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [unlock sensor]).

WIRING DIAGRAM


B281953E15


INSPECTION PROCEDURE

NOTICE:
  1. The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the power switch off to troubleshoot:
    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (Click here).
  6. After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
  1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (UNLOCK DETECTION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FL Door Lock Pos*1
    Front LH door unlock detection switch signal / UNLOCK or LOCK
    UNLOCK: Front LH door unlocked
    LOCK: Front LH door locked
    -
    FR Door Lock Pos*2
    Front RH door unlock detection switch signal / UNLOCK or LOCK
    UNLOCK: Front RH door unlocked
    LOCK: Front RH door locked
    -

    1. *1: for LHD
    2. *2: for RHD



NG
GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit) (Click here)
OK


3.READ VALUE USING INTELLIGENT TESTER (UNLOCK SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry&Start or Main Body / Data List.

  1. Turn the intelligent tester on.


Entry&Start 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D-Door Touch Sensor
Driver door touch sensor (unlock sensor) / ON or OFF
ON: Driver door touch sensor (unlock sensor) touched
OFF: Driver door touch sensor (unlock sensor) not touched
  1. Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
  2. Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.

OK:
The intelligent tester display changes correctly in response to the operation of the front door outside handle assembly (for driver door).



NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
  1. Disconnect the W1*1 or V1*2 front door outside handle assembly (for driver door) connector.

  1. Disconnect the I86 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    1. *1: for LHD
    2. *2: for RHD

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    W1-4 (SENS) - I86-3 (SEN1)
    Always
    Below 1 Ω
    I86-1 (E) - Body ground
    Always
    Below 1 Ω
    W1-4 (SENS) or I86-3 (SEN1) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    V1-4 (SENS) - I86-3 (SEN1)
    Always
    Below 1 Ω
    I86-1 (E) - Body ground
    Always
    Below 1 Ω
    V1-4 (SENS) or I86-3 (SEN1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) (DRIVER DOOR UNLOCK SENSOR SIGNAL INPUT)


  1. Connect the W1*1 or V1*2 front door outside handle assembly (for driver door) connector.


    B282015E05


    Text in Illustration 
    *1
    Waveform
    -
    -
    *a
    Component with harness connected
    (Certification ECU (smart key ECU assembly))
    *b
    In actuality, sampling is being performed
    1. *1: for LHD
    2. *2: for RHD

  1. Connect the I86 certification ECU (smart key ECU assembly) connector.

  1. Using an oscilloscope, check the waveform.

    OK:

    Tester Connection
    Switch Condition
    Tool Setting
    Specified Condition
    I86-3 (SEN1) - I86-1 (E)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors locked
    4. Electrical key transmitter sub-assembly not sufficiently close to vehicle
    5. Driver door unlock sensor not touched → touched
    2 V/DIV., 500 ms/DIV.
    Pulse generation (See waveform)



NG
REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FRONT DRIVER DOOR) (Click here)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)