Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM

DTC    C1AEC    Front Sensor Communication Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the front sensors and the ECU, or when there is a malfunction in a front sensor.

DTC No.
DTC Detection Condition
Trouble Area
C1AEC
An open or short circuit in the communication line between the front sensors and ECU or a malfunction in a front sensor during initialization mode after the power switch is turned on (IG).
  1. Front ultrasonic sensor circuit
  2. Clearance warning ECU assembly

WIRING DIAGRAM


E231492E03


INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (C1AEC)
  1. Check for DTCs (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1AEC is output
    A
    No DTCs are output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - FRONT LEFT SENSOR)
  1. Disconnect the I82 connector from the clearance warning ECU assembly.

  1. Disconnect the D2 connector from the No. 1 ultrasonic sensor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I82-4 (BOF) - D2-1 (BI)
    Always
    Below 1 Ω
    I82-8 (SOF) - D2-3 (SI)
    Always
    Below 1 Ω
    I82-6 (E5) - D2-5 (EI)
    Always
    Below 1 Ω
    I82-4 (BOF) - Body ground
    Always
    10 kΩ or higher
    I82-8 (SOF) - Body ground
    Always
    10 kΩ or higher
    I82-6 (E5) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (FRONT LEFT SENSOR - FRONT RIGHT SENSOR)
  1. Disconnect the Z2 connector from the No. 1 ultrasonic sensor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D2-2 (BO) - Z2-1 (BI)
    Always
    Below 1 Ω
    D2-4 (SO) - Z2-3 (SI)
    Always
    Below 1 Ω
    D2-6 (EO) - Z2-5 (EI)
    Always
    Below 1 Ω
    D2-2 (BO) - Body ground
    Always
    10 kΩ or higher
    D2-4 (SO) - Body ground
    Always
    10 kΩ or higher
    D2-6 (EO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT NO. 1 ULTRASONIC SENSOR (FRONT LEFT SENSOR)


    E227022E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (BI) - 5 (EI)
    Always
    10 kΩ or higher
    1 (BI) - 2 (BO)
    Always
    10 kΩ or higher
    3 (SI) - 4 (SO)
    Always
    Below 1 Ω
    5 (EI) - 6 (EO)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (No. 1 Ultrasonic Sensor (Front Left Sensor))



NG
REPLACE NO. 1 ULTRASONIC SENSOR (FRONT LEFT SENSOR) (Click here)
OK


5.REPLACE NO. 1 ULTRASONIC SENSOR (FRONT LEFT SENSOR)
  1. Replace the No. 1 ultrasonic sensor (front left sensor) with a known good one (Click here).

    HINT:
    All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.


NEXT


6.CHECK DTC OUTPUT (C1AEC)
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1AEC is output
    A
    No DTCs are output
    B



B
END (FRONT LEFT SENSOR WAS DEFECTIVE)
A


7.REPLACE NO. 1 ULTRASONIC SENSOR (FRONT RIGHT SENSOR)
  1. Replace the No. 1 ultrasonic sensor (front right sensor) with a known good one (Click here).

    HINT:
    All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.


NEXT


8.CHECK DTC OUTPUT (C1AEC)
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1AEC is output
    A
    No DTCs are output
    B



B
END (FRONT RIGHT SENSOR WAS DEFECTIVE)
A

REPLACE CLEARANCE WARNING ECU ASSEMBLY (Click here)