CYLINDER HEAD GASKET > INSTALLATION |
| 1. INSPECT CYLINDER HEAD BOLT |
![]() |
Using a vernier caliper, measure the diameter of the threads at the measurement point.
| *a | Measurement Point |
| 2. INSPECT CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head contacts the cylinder block and manifold.
| Item | Specified Condition |
| Cylinder head lower side | 0.05 mm (0.00197 in.) |
| Intake manifold side | 0.10 mm (0.00394 in.) |
| Exhaust manifold side | 0.10 mm (0.00394 in.) |
| *a | Cylinder Head Lower Side |
| *b | Intake Manifold Side |
| *c | Exhaust Manifold Side |
![]() |
Using a dye penetrant, check the intake ports, exhaust ports and cylinder head surface for cracks.
If cracked, replace the cylinder head.
| 3. INSTALL CYLINDER HEAD GASKET |
![]() |
Clean the cylinder block and cylinder head with solvent.
| *1 | Cylinder Head Gasket |
| *2 | Cylinder Block |
| *a | Lot No. |
| *b | 3.0 mm or more |
| *c | 20 mm or more |
![]() | Seal Packing |
![]() | Front |
Apply a continuous line of seal packing to a new cylinder head gasket as shown in the illustration.
Place a new cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp facing upward.
| 4. INSTALL CYLINDER HEAD SUB-ASSEMBLY |
Place the cylinder head on the cylinder block.
Install the plate washers to the cylinder head bolts.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.
Step 1:
![]() |
Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts in several steps, in the sequence shown in the illustration.
Step 2:
Tighten the cylinder head bolts again in the sequence shown in the illustration to make sure that they are tightened to the specified torque.
Step 3:
![]() |
Mark each cylinder head bolt head with paint as shown in the illustration.
![]() | Front |
| *a | Painted Mark |
Tighten the cylinder head bolts 90° in the sequence shown in step 1.
Step 4:
Tighten the cylinder head bolts another 90° in the sequence shown in step 1.
Check that the paint marks are now facing rearward.
| 5. INSTALL VALVE STEM CAP |
Apply a light coat of engine oil to the valve stem ends.
Install the 16 valve stem caps to the cylinder head.
| 6. SET CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Check the camshaft timing gear position.
| *1 | Knock Pin Hole |
| *2 | Alignment Mark |
| *a | Advanced Position: |
| *b | Retarded Position: |
![]() |
Align and attach the knock pin of the No. 1 camshaft with the pin hole of the camshaft timing gear.
| *1 | Pin Hole |
| *2 | Knock Pin |
![]() |
Check that there is no clearance between the camshaft timing gear and camshaft flange.
| *1 | Camshaft Timing Gear |
| *2 | Flange |
| *a | INCORRECT |
| *b | CORRECT |
| *c | Clearance |
| *d | No Clearance |
Secure the camshaft in place by hand, and then install the installation bolt of the camshaft timing gear by hand.
![]() |
Release the lock pin.
| *1 | Rubber |
| *2 | Vinyl Tape |
| *3 | Knock Pin |
| *a | Retard Side Path |
| *b | Advance Side Path |
| *c | Open |
| *d | Close |
Clean the camshaft journal with non-residue solvent.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Open a hole at port A shown in the illustration.
![]() |
While applying approximately 200 kPa (2.0 kgf/ cm2, 29 psi) of air pressure to the oil path, forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).
Remove the vinyl tape and rubber pieces from the camshaft.
Remove the bolt and camshaft timing gear.
| 7. INSTALL VALVE LASH ADJUSTER ASSEMBLY |
Inspect the valve lash adjuster before installing it .
Install the 16 lash adjusters to the cylinder head.
| 8. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
![]() |
Apply engine oil to the lash adjuster tips and valve stem caps.
| *1 | Valve Rocker Arm |
| *2 | Valve Lash Adjuster |
| *3 | Valve Stem Cap |
Install the 16 valve rocker arms as shown in the illustration.
| 9. INSTALL NO. 2 CAMSHAFT BEARING |
Clean the No. 2 camshaft bearing.
![]() |
Install the No. 2 camshaft bearing to the camshaft housing sub-assembly.
| *1 | Vernier Caliper |
Using a vernier caliper, measure the distance between the camshaft housing edge and the No. 2 camshaft bearing edge.
| 10. INSTALL NO. 1 CAMSHAFT BEARING |
Clean the No. 1 camshaft bearing.
![]() |
Install the No. 1 camshaft bearing to the No. 1 camshaft bearing cap.
| *1 | Vernier Caliper |
Using a vernier caliper, measure the distance between the No. 1 camshaft bearing cap edge and the No. 1 camshaft bearing edge.
| 11. INSTALL OIL CONTROL VALVE FILTER |
![]() |
Install the oil control valve filter to the No. 1 camshaft bearing cap.
| 12. INSTALL CAMSHAFT |
Clean the camshaft journals, camshaft housing and bearing caps.
Apply a light coat of engine oil to the camshaft journal, camshaft housing and bearing caps.
Install the camshaft and No. 2 camshafts to the camshaft housing.
| 13. INSTALL CAMSHAFT BEARING CAP |
![]() |
Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.
![]() |
Install the 11 bolts in the order shown in the illustration.
| 14. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY |
![]() |
Check that the valve rocker arms are installed as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Valve Stem Cap |
| *3 | Valve Lash Adjuster |
| *a | INCORRECT |
| *b | CORRECT |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
![]() |
Position the knock pin of the No. 1 and No. 2 camshafts as shown in the illustration.
| *1 | Knock Pin |
| *a | Approximately 17° |
| *b | Approximately 2° |
![]() |
Install the camshaft housing, and then install the 20 bolts in the order shown in the illustration.
| 15. INSTALL CAMSHAFT TIMING SPROCKET |
![]() |
Using a wrench to hold the hexagonal portion of the No. 2 camshaft, and install the camshaft timing sprocket with the bolt.
| *a | Hold |
| *b | Turn |
| 16. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Check the camshaft timing gear position.
| *1 | Knock Pin Hole |
| *2 | Alignment Mark |
![]() |
Align and attach the knock pin of the No. 1 camshaft with the pin hole of the camshaft timing gear.
| *1 | Pin Hole |
| *2 | Knock Pin |
![]() |
Check that there is no clearance between the camshaft timing gear and camshaft flange.
| *1 | Camshaft Timing Gear |
| *2 | Flange |
| *a | INCORRECT |
| *b | CORRECT |
| *c | Clearance |
| *d | No Clearance |
![]() |
Using a wrench to hold the hexagonal portion of the No. 1 camshaft, install the bolt.
| *a | Hold |
| *b | Turn |
| 17. ADD ENGINE OIL |
![]() |
Add 50 cc (3.1 cu. in) of engine oil into the oil hole shown in the illustration.
| 18. INSTALL NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Install the chain vibration damper with the 2 bolts.
| 19. SET NO. 1 CYLINDER TO TDC/COMPRESSION |
![]() |
Temporarily install the crankshaft pulley bolt.
Rotate the crankshaft 40° counterclockwise to position the crankshaft pulley key as shown in the illustration.
![]() |
Check that the timing marks of the camshaft timing gears are as shown in the illustration.
| *a | Timing Mark |
| *b | Approximately 7° |
| *c | Approximately 32° |
| 20. INSTALL CHAIN SUB-ASSEMBLY |
Place the chain onto the camshaft timing gears and crankshaft timing sprocket.
![]() |
Align the mark plate (yellow or gold) of the chain with the timing mark of the camshaft timing sprocket and install the chain to the camshaft timing sprocket.
| *a | Mark Plate |
| *b | Timing Mark |
![]() |
Align the mark plate (pink or gold) of the chain with the timing mark of the crankshaft timing sprocket and install the chain to the crankshaft timing sprocket.
| *1 | Mark Plate |
| *2 | Timing Mark |
![]() |
Tie a string above the crankshaft timing sprocket so that the chain is secure.
![]() |
Using the hexagonal portion of the intake camshaft, rotate the intake camshaft counterclockwise with a wrench, align the timing mark of the camshaft timing gear with the mark plate (yellow or gold) of the chain and install the chain to the camshaft timing gear.
| *1 | Mark Plate |
| *2 | Timing Mark |
![]() |
Remove the string above the crankshaft timing sprocket, rotate the crankshaft clockwise, and loosen the chain so that the chain tensioner slipper can be installed.
| 21. INSTALL CHAIN TENSIONER SLIPPER |
![]() |
Install the chain tensioner slipper with the bolt.
| 22. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Install a new gasket and the chain tensioner with the 2 bolts.
Remove the pin from the stopper plate.
| 23. INSTALL TIMING CHAIN GUIDE |
![]() |
Install the timing chain guide with the bolt.
| 24. SET NO. 1 CYLINDER TO TDC/COMPRESSION |
Temporarily install the crankshaft pulley bolt.

| *a | Approximately 7° | *b | Approximately 32° |
| *c | Timing Mark | *d | Crankshaft pulley set key |
Rotate the crankshaft clockwise, and check that the timing marks on the crankshaft timing sprocket and camshaft timing gears are as shown in the illustration.
Remove the crankshaft pulley bolt.
| 25. INSTALL INTAKE MANIFOLD |
Temporarily install the intake manifold with the 6 bolts.
![]() |
Tighten the 6 bolts in the order shown in the illustration.
Connect the 6 wire harness clamps.
Connect the heated oxygen sensor connector.
Connect the No. 2 ventilation hose.
| 26. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY |
![]() |
Install 4 new injector vibration insulators to the cylinder head.
| *1 | Fuel Delivery Spacer |
| *a | Fuel Delivery Pipe Side |
| *b | Cylinder Head Side |
Install the 2 fuel delivery spacers onto the cylinder head.
![]() |
Install the fuel delivery pipe sub-assembly with the 4 fuel injector assemblies and install the 2 bolts.
Connect the 4 fuel injector connectors.
| 27. INSTALL NO. 1 WATER BY-PASS PIPE |
![]() |
Install the No. 1 water by-pass pipe with the 2 bolts.
| *1 | Clamp |
Connect the 2 clamps.
| 28. INSTALL NO. 3 WATER BY-PASS PIPE |
Install the No. 3 water by-pass pipe with the 2 bolts.
Connect the No. 5 water by-pass hose with the clamp.
| 29. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY |
Set a new gasket to the cylinder head sub-assembly.
Temporarily install the exhaust manifold converter sub-assembly with the 5 nuts.
Temporarily install the No. 2 manifold stay and manifold stay with the 2 bolts and 2 nuts.
![]() |
Tighten the 5 nuts in the order shown in the illustration.
| 30. INSTALL NO. 2 MANIFOLD STAY |
![]() |
Tighten the bolt and nut in the order shown in the illustration.
| 31. INSTALL MANIFOLD STAY |
![]() |
Tighten the bolt and nut in the order shown in the illustration.
| 32. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
Install the No. 1 exhaust manifold heat insulator with the 4 bolts.
| 33. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY |
Install a new gasket to the intake manifold.
Install the throttle with motor body assembly with the 4 bolts.
Connect the throttle body connector.
Connect the 2 water by-pass hoses to the throttle with motor body assembly.
Connect the 2 hoses.
| 34. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY |