Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function)

DTC    B27A2    Open in Front Passenger Side Electrical Antenna Circuit

for Preparation Click here


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for front passenger door) [electrical key antenna] at intervals of 0.25 seconds. For the front door outside handle assembly (for front passenger door) [electrical key antenna] to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the front passenger door at intervals of 0.25 seconds. DTC B27A2 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [electrical key antenna] (between terminals CLG2 and ANT1, or terminals CG2B and ANT2).

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B27A2
An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) (CLG2 - ANT1, CG2B - ANT2) (1 trip detection logic*).
  1. Wire harness or connector
  2. Front door outside handle assembly (for front passenger door)
  3. Certification ECU (smart key ECU assembly)
Any time
  1. *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for front passenger door
-

Related Data List and Active Test 
DTC Code
Data List and Active Test
B27A2
Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM


B281953E16


INSPECTION PROCEDURE

NOTICE:
  1. The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the power switch off to troubleshoot:
    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (Click here).
  4. After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
  5. The front door outside handle assembly (for front passenger door) has an antenna coil between ANT1 and ANT2 terminals.

1.CHECK CONNECTOR CONNECTION
  1. Turn the power switch off.

  1. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)
  1. Disconnect the I87 and I86 certification ECU (smart key ECU assembly) connectors.

  1. Disconnect the V1*1 or W1*2 front door outside handle assembly (for front passenger door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    1. *1: for LHD
    2. *2: for RHD

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I86-13 (CLG2) - V1-6 (ANT1)
    Always
    Below 1 Ω
    I86-12 (CG2B) - V1-3 (ANT2)
    Always
    Below 1 Ω
    I86-1 (E) - Body ground
    Always
    Below 1 Ω
    V1-2 (GND) - Body ground
    Always
    Below 1 Ω
    I86-13 (CLG2) or V1-6 (ANT1) - Body ground
    Always
    10 kΩ or higher
    I86-12 (CG2B) or V1-3 (ANT2) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I86-13 (CLG2) - W1-6 (ANT1)
    Always
    Below 1 Ω
    I86-12 (CG2B) - W1-3 (ANT2)
    Always
    Below 1 Ω
    I86-1 (E) - Body ground
    Always
    Below 1 Ω
    W1-2 (GND) - Body ground
    Always
    Below 1 Ω
    I86-13 (CLG2) or W1-6 (ANT1) - Body ground
    Always
    10 kΩ or higher
    I86-12 (CG2B) or W1-3 (ANT2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER SIDE ELECTRICAL KEY ANTENNA)


  1. Connect the I87 and I86 certification ECU (smart key ECU assembly) connectors.


    B282004E04


    Text in Illustration 
    *1
    Waveform 1
    *2
    Waveform 2
    *a
    Component with harness connected
    (Certification ECU (smart key ECU assembly))
    -
    -

  1. Connect the V1*1 or W1*2 front door outside handle assembly (for front passenger door) connector.

  1. Using an oscilloscope, check the waveform.

    OK:

    Tester Connection
    Switch Condition
    Tool Setting
    Specified Condition
    I86-13 (CLG2) - I86-1 (E)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought inside detection area*3
    6. All doors locked through wireless operation
    2 V/DIV., 500 ms/DIV.
    Pulse generation (See waveform 1)
    I86-13 (CLG2) - I86-1 (E)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought outside detection area*4
    6. All doors locked through wireless operation
    2 V/DIV., 500 ms/DIV.
    Pulse generation (See waveform 2)
    I86-12 (CG2B) - I86-1 (E)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. All doors locked through wireless operation
    2 V/DIV., 500 ms/DIV.
    Pulse generation (See waveform 2)

    1. *1: for LHD
    2. *2: for RHD
    3. *3: For details about the areas that are inside the entry function detection area, refer to Operation Check (Click here).
    4. *4: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)
  1. Temporarily replace the front door outside handle assembly (for front passenger door) with a new or known good one (Click here).


NEXT


5.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


6.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B27A2 is not output.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) WAS DEFECTIVE)