Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Harness or connector
  2. Speaker
  3. Radio and display receiver assembly

WIRING DIAGRAM



E226481E05


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the radio and display receiver assembly and speakers.

  1. Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I152-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    I152-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    I152-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    I152-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    I153-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    I153-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    I153-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    I153-6 (RL-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I83-3 (+) - Body ground
    Always
    10 kΩ or higher
    I83-1 (-) - Body ground
    Always
    10 kΩ or higher
    I1-3 (+) - Body ground
    Always
    10 kΩ or higher
    I1-1 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


  1. Resistance check



      E219303E17
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J5-1 - J5-2
      Always
      3.2 to 4.8 Ω
      K5-1 - K5-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


  1. Resistance check



      E226097E04
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I83-2 (TWR-) - I83-4 (TWR+)
      Always
      10 kΩ or higher
      I83-1 (-) - I83-2 (TWR-)
      Always
      Below 1 Ω
      I83-3 (+) - I83-4 (TWR+)
      Always
      Below 1 Ω
      I1-2 (TWL-) - I1-4 (TWL+)
      Always
      10 kΩ or higher
      I1-1 (-) - I1-2 (TWL-)
      Always
      Below 1 Ω
      I1-3 (+) - I1-4 (TWL+)
      Always
      Below 1 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
  1. Check that the malfunction disappears when a known good speaker is installed (Click here).

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 5
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE) 

5.INSPECT REAR SPEAKER ASSEMBLY


  1. Resistance check



      E219303E18
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O18-1 - O18-2
      Always
      3.2 to 4.8 Ω
      O21-1 - O21-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)