CAN COMMUNICATION SYSTEM > DIAGNOSIS SYSTEM |
| ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM |
V Bus
ECM
Multiplex network body ECU
Brake booster with master cylinder assembly (Skid control ECU)
Radio and display receiver assembly
Power steering ECU assembly
Air conditioning amplifier assembly
Airbag sensor assembly
Smart key ECU assembly (Certification ECU)
Clearance warning ECU assembly*1
Power management control ECU
Steering sensor
Combination meter assembly
Sub Bus 15
ECM
Brake booster with master cylinder assembly (Skid control ECU)
Power management control ECU
| CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT ADOPT CAN COMMUNICATION |
The systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed on the vehicle.
| ECU / Sensor Name | Intelligent Tester Display | Applicability |
| ECM | ECM (Engine) | Installed on all vehicles |
| Multiplex network body ECU | Main Body | Installed on all vehicles |
| Brake booster with master cylinder assembly (Skid control ECU) | Skid Control (ABS/VSC/TRAC) | Installed on all vehicles |
| Radio and display receiver assembly | Display and Navigation (AVN1) | Vehicles with audio and visual system |
| Power steering ECU assembly | Power Steering (EPS) | Installed on all vehicles |
| Air conditioning amplifier assembly | Air Conditioning Amplifier | Installed on all vehicles |
| Airbag sensor assembly | Airbag | Installed on all vehicles |
| Smart key ECU assembly (Certification ECU) | Certification (Smart) | Installed on all vehicles |
| Clearance warning ECU assembly | Clearance Warning (Clearance Sonar2) | Installed on RHD vehicles |
| Power management control ECU |
| Installed on all vehicles |
| Steering sensor | Spiral cable (Steering Angle Sensor) | Installed on all vehicles |
| Combination meter assembly | Combination Meter | Installed on all vehicles |
| BUS CHECK (COMMUNICATION BUS CHECK) |
![]() |
Select "Bus Check" from the "System Select" screen on the intelligent tester.
![]() |
Select "Communication Bus Check" from the "Bus Check" screen.
![]() |
The screen displays the ECUs and sensors that are properly connected to the CAN communication system.
![]() |
"There is no system connected to the communication bus" is displayed if there are no ECUs or sensors connected to the CAN bus.
![]() |
The default item displayed in the pull down menu is "ALL". When checking the ECUs (sensors) connected to each bus, open the pull down menu and select the bus to be checked from the pull down menu. The pull down menu displays "ALL", "V Bus", and the names of the remaining buses.
| Pull Down Menu | Display Content |
| ALL | All ECUs (sensors) connected to the CAN bus |
| V Bus | ECUs (sensors) connected to the V Bus |
| Bus Name | ECUs (sensors) connected to the selected bus |
| *a | Pull down menu |
| *b | List |
| *c | Example of displayed item |
| *d | Bus (V bus or sub bus) selected using pull down menu. |
| Bus Type | Background Color | Connection Status |
| V Bus | White | Communication has been normal since the start of the communication bus check. |
| Yellow | Communication stop occurred at least once since the start of the communication bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the communication bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the communication bus check.*1 | |
| Sub bus (gateway function equipped ECU that does not have history of connected ECUs)*2 | White | Communication has been normal since the start of the communication bus check. |
| Yellow | Communication stop occurred at least once since the start of the communication bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the communication bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the communication bus check.*1 | |
| Sub bus (gateway function equipped ECU that has history of connected ECUs)*3 | White | Communication has been normal since the start of the communication bus check. |
| Yellow | Communication stop occurred at least once since the start of the communication bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
| |
| Not displayed | Either of the following:
|
Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.
| HOW TO INTERPRET BUS CHECK (COMMUNICATION BUS CHECK) SCREEN |
When a communication stop is currently occurring, the probable malfunctioning part can be determined from the communication bus check and by using the following methods.
If a communication error of only 1 ECU or sensor is indicated on the Communication Bus Check screen, a communication stop of the ECU or sensor is suspected.
Example: Open in both CAN branch lines of ECU B on the V bus

| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of malfunction |
| *e | Not displayed or background color changes to red or yellow | *f | Communication Bus Check screen |
![]() |
If communication errors for multiple ECUs or sensors are indicated on the Communication Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or a sensor which is not displayed) is suspected.
Example: Open in a CAN branch line for ECU D on the V bus
| *a | Background color periodically changes to yellow or red |
| *b | Not displayed or background color is yellow or red |
| *c | Not displayed |
| Bus Type | Background Color | Connection Status |
| V Bus | White | Communication has been normal since the start of the communication bus check. |
| Yellow | Communication stop occurred at least once since the start of the communication bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the communication bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the communication bus check.*1 | |
| Sub bus (gateway function equipped ECU that does not have history of connected ECUs)*2 | White | Communication has been normal since the start of the communication bus check. |
| Yellow | Communication stop occurred at least once since the start of the communication bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the communication bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the communication bus check.*1 | |
| Sub bus (gateway function equipped ECU that has history of connected ECUs)*3 | White | Communication has been normal since the start of the communication bus check. |
| Yellow | Communication stop occurred at least once since the start of the communication bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
| |
| Not displayed | Either of the following:
|
![]() |
If a communication error is indicated on both the V bus and sub bus on the Communication Bus Check screen, suspect any communication stop displayed for the V bus first.
Example: Open in both CAN branch lines of ECU C on the V bus
| *a | Not displayed or background color changes to red |
![]() |
If the Communication Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.
Example: Open in both CAN branch lines of ECU G on the sub bus
| *a | Background color changes to red |
If both of the V bus main bus lines are open, ECUs or sensors that are located farther away from the DLC3 than the open part will be displayed as a communication stop on the Communication Bus Check screen.
(In this case, ECU A and B are not displayed or their background color changes to red.)

| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of malfunction |
| *e | Not displayed or background color is red | *f | Communication Bus Check screen |
If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the Communication Bus Check screen.
(In this case, ECU I and J are not displayed or their background color changes to red.)

| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of malfunction |
| *e | Not displayed or background color is red | *f | Communication Bus Check screen |
| *g | Gateway function equipped ECU | - | - |
![]() |
When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the Communication Bus Check screen.
| *a | When any of the following malfunctions occur on the V bus |
| *b | When any of the following malfunctions occur on a sub bus |
| *c | Not displayed |
| Short between CAN lines (CANH and CANL) |
| Short between a CAN line (CANH or CANL) and +B |
| Short between a CAN line (CANH or CANL) and ground |
| Open in a CAN main bus line |
| BUS CHECK (COMMUNICATION MALFUNCTION DTC) |
![]() |
Select "Bus Check" from the "System Select" screen on the intelligent tester.
![]() |
Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".
![]() |
Select the system to be checked for DTCs and select "Details".
![]() |
CAN communication system DTCs are output.
| HOW TO INTERPRET COMMUNICATION DTCS (DTCS THAT START WITH U) |
If a CAN communication error cannot be reproduced, determine the suspected malfunctioning part using the DTCs stored in ECUs that are connected to the CAN buses by following the procedure below.
If multiple ECUs store a communication DTC for a particular ECU, a communication stop of the ECU is suspected.

| *a | Items to be checked | - | - |
If almost all of the communication DTCs of an ECU are stored, a communication stop of the ECU is suspected.

| *a | Items to be checked | - | - |
To help determine the part of the sub bus that has a communication error, prioritize the communication stop DTCs stored in the gateway function equipped ECU.

| *a | Items to be checked | *b | ECM |
| *c | Gateway function equipped ECU | *d | Location of malfunction |
| *e | V Bus | *f | Sub bus |
When any of the following malfunctions occurs, many DTCs are likely to be output from many ECUs. Because of this, it may be difficult to determine the probable malfunctioning part.
| DTC TABLE BY ECU |
Power Management Control ECU / Intelligent Tester Display "Hybrid Control"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100 | Lost Communication with ECM / PCM "A" | The power management control ECU (HV CPU) does not receive data from the ECM for 0.58 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait 1.58 seconds or more. | HV system warning light turns on. MIL illuminates. | DTC is stored until it is cleared using the intelligent tester. |
| U0110*1 | Lost Communication with Drive Motor Control Module "A" | Either condition is met:
| Both conditions are met:
| Turn the power switch on (IG) and wait 0.21 seconds or more. | HV system warning light turns on. | DTC is stored until it is cleared using the intelligent tester. |
| U0129 | Lost Communication with Brake System Control Module | The power management control ECU (HV CPU) does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.34 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait 4.44 seconds or more. | HV system warning light turns on. | DTC is stored until it is cleared using the intelligent tester. |
| U0140 | Communication Error from Body ECU to HV ECU | The power management control ECU (HV CPU) does not receive data from the multiplex network body ECU for 3.6 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait 4.6 seconds or more. | HV system warning light turns on. | DTC is stored until it is cleared using the intelligent tester. |
| U0151 | Communication Error from Airbag ECU to HV ECU | The power management control ECU (HV CPU) does not receive data from the airbag sensor assembly for 10.6 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait 11.6 seconds or more. | HV system warning light turns on. | DTC is stored until it is cleared using the intelligent tester. |
| U0164 | Communication Error from A/C ECU to HV ECU | The power management control ECU (HV CPU) does not receive data from the air conditioning amplifier assembly for 10.6 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait 11.6 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
| U029A*2 | Lost Communication with Hybrid Battery Pack Sensor Module | The power management control ECU (HV CPU) does not receive data from the battery smart unit for 0.5 seconds or more. | The power switch is turned on (IG) for 0.5 seconds or more. | Turn the power switch on (IG) and wait 1 second or more. | HV system warning light turns on. | DTC is stored until it is cleared using the intelligent tester. |
| U0424*1 | Invalid Data Received from HVAC Control Module | The power management control ECU (HV CPU) receives an abnormal operation value command from the air conditioning amplifier assembly for 3 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait 3.5 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
| U1107 | Lost Communication with Power Management Module | The power management control ECU (HV CPU) does not receive data from the power management control ECU (power management CPU) for 3.6 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait 4.6 seconds or more. | HV system warning light turns on. | DTC is stored until it is cleared using the intelligent tester. |
Power Management Control ECU / Intelligent Tester Display "Power Source Control"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0140 | Lost Communication with Main Body ECU | The power management control ECU (power management CPU) does not receive data from the multiplex network body ECU for 3.1 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait 20 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0155 | Lost Communication with Combination Meter | The power management control ECU (power management CPU) does not receive data from the combination meter assembly for 3.1 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait 20 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0293*1 | Lost Communication with HV ECU | The power management control ECU (power management CPU) does not receive data from the power management control ECU (HV CPU) for 3.1 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait 13.1 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
Power Management Control ECU / Intelligent Tester Display "Cruise Control"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0122 | Lost Communication with Vehicle Dynamics Control Module | While the cruise control system is on (the system has been switched on using the ON/OFF button on the cruise control switch), the power management control ECU (HV CPU) does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.62 seconds or more. | Both conditions are met:
| After turning the power switch on (IG), turn the cruise control main switch on and wait for at least 4.72 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the intelligent tester. |
ECM / Intelligent Tester Display "Engine and ECT"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0293 | Lost Communication with HV ECU | The ECM does not receive data from the power management control ECU (HV CPU) for 0.576 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait 5 seconds or more. | MIL illuminates. | DTC is stored until it is cleared using the intelligent tester. |
Power Steering ECU Assembly / Intelligent Tester Display "EMPS"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0129 | Lost Communication with Brake System Control Module | The power steering ECU assembly cannot receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.3 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait 4.3 seconds or more. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
| U0293 | Lost Communication with Hybrid Control Module | The power steering ECU assembly cannot receive data from the power management control ECU (HV CPU) for 5 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait 7 seconds or more. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
Brake Booster with Master Cylinder Assembly (Skid Control ECU) / Intelligent Tester Display "ABS/VSC/TRC"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0073 | Control Module Communication Bus OFF | One of the following conditions is met:
| Both conditions are met:
| Turn the power switch on (IG) and wait 60 seconds or more. | <When data can be sent to the combination meter>
| DTC is stored until it is cleared using the intelligent tester. |
<When data cannot be sent to the combination meter>
| ||||||
| U0123 | Lost Communication with Yaw Rate Sensor Module | One of the following conditions is met:
| Both conditions are met:
| Turn the power switch on (IG) and wait 60 seconds or more. |
| DTC is stored until it is cleared using the intelligent tester. |
| U0124 | Lost Communication with Lateral Acceleration Sensor Module | One of the following conditions is met:
| Both conditions are met:
| Turn the power switch on (IG) and wait 60 seconds or more. |
| DTC is stored until it is cleared using the intelligent tester. |
| U0126 | Lost Communication with Steering Angle Sensor Module | One of the following conditions is met:
| Both conditions are met:
| Turn the power switch on (IG) and wait 60 seconds or more. | Slip warning light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
| U0293 | Communication Error from HV ECU | One of the following conditions is met:
| Both conditions are met:
| Turn the power switch on (IG) and wait 60 seconds or more. |
| DTC is stored until it is cleared using the intelligent tester. |
Steering Sensor / Intelligent Tester Display "Spiral cable (Steering Angle Sensor)"
Airbag Sensor Assembly / Intelligent Tester Display "Airbag"
Multiplex Network Body ECU / Intelligent Tester Display "Main Body"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100 | Lost Communication with ECM / PCM "A" | The multiplex network body ECU does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0101 | Lost Communication with ECT | The multiplex network body ECU does not receive data from the power management control ECU (HV CPU) for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0120 | Lost Communication With Starter / Generator Control Module | The multiplex network body ECU does not receive data from the power management control ECU (power management CPU) for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0151 | Communication Error from Airbag ECU to HV ECU | The multiplex network body ECU does not receive data from the airbag sensor assembly for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0155 | Lost Communication with Combination Meter | The multiplex network body ECU does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0164 | Communication Error from A/C ECU to HV ECU | The multiplex network body ECU does not receive data from the air conditioning amplifier assembly for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0293 | Communication Error from HV ECU | The multiplex network body ECU does not receive data from the power management control ECU (HV CPU) for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0327 | Software Incompatibility with Vehicle Security Control Module | The multiplex network body ECU does not receive data from the smart key ECU assembly (certification ECU) for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
Smart Key ECU Assembly (Certification ECU) / Intelligent Tester Display "Entry&Start"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100 | Lost Communication with ECM | The smart key ECU assembly (certification ECU) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0142 | Lost Communication with Main Body ECU | The smart key ECU assembly (certification ECU) does not receive data from the multiplex network body ECU for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0155 | Lost Communication with Combination Meter | The smart key ECU assembly (certification ECU) does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0293 | Lost Communication with HV ECU | The smart key ECU assembly (certification ECU) does not receive data from the power management control ECU (HV CPU) for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
Air Conditioning Amplifier Assembly / Intelligent Tester Display "Air Conditioner"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0131 | Lost Communication with Electric Power Steering ECU | The air conditioning amplifier assembly does not receive data from the power steering ECU assembly for 5 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0142 | Lost Communication with Main Body ECU | The air conditioning amplifier assembly does not receive data from the multiplex network body ECU for 5 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0155 | Lost Communication with Combination Meter | The air conditioning amplifier assembly does not receive data from the combination meter assembly for 5 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0293 | Lost Communication with HV ECU | The air conditioning amplifier assembly does not receive data from the power management control ECU (HV CPU) for 5 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
Combination Meter Assembly / Intelligent Tester Display "Combination Meter"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100 | Lost Communication with ECM / PCM "A" | The combination meter assembly does not receive data from the ECM or power management control ECU (HV CPU) for 2 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 2 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0129 | Lost Communication with Skid Control ECU | The combination meter assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2 seconds or 3 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 2 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0131 | Lost Communication with Power Steering Control Module | The combination meter assembly does not receive data from the power steering ECU assembly for 3 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 3 seconds. | EPS warning light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
| U0142 | Lost Communication with Main Body ECU | The combination meter assembly does not receive data from the multiplex network body ECU for 3 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 3 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0151 | Lost Communication with Airbag ECU | The combination meter assembly does not receive data from the airbag sensor assembly for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 10 seconds. | SRS warning light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
Radio and Display Receiver Assembly / Intelligent Tester Display "Navigation System"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0073 | Sending Malfunction (Navigation to APGS) | The radio and display receiver assembly does not send/receive data for 10 seconds or more. | Both conditions are met:
| Turn the power switch on (ACC) and wait at least 11.08 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0100 | Lost Communication with ECM / PCM "A" | The radio and display receiver assembly does not receive data from the power management control ECU for 10 seconds or more. | All conditions are met:
| Drive the vehicle at a speed of 20 km/h (12 mph) or more for 11 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0129 | Lost Communication with Brake System Control Module | The radio and display receiver assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 1 second or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 2 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0140 | Lost Communication with Body Control Module | The radio and display receiver assembly does not receive data from the multiplex network body ECU for 4 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0155 | Meter ECU Communication | The radio and display receiver assembly does not receive data from the combination meter assembly for 30 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 31 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0293 | Lost Communication with HV ECU | The radio and display receiver assembly does not receive data from the power management control ECU (HV CPU) for 4 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
Clearance Warning ECU Assembly / Intelligent Tester Display "Clearance Sonar"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100 | Lost Communication with ECM / PCM "A" | The clearance warning ECU assembly does not receive data from the ECM for 5.75 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 7.75 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0101 | Lost Communication with TCM | The clearance warning ECU assembly does not receive data from the power management control ECU (HV CPU) for 8.07 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 10.07 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0142 | Lost Communication with Body Control Module "B" | The clearance warning ECU assembly does not receive data from the multiplex network body ECU for 5.9 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 7.9 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0155 | Lost Communication with Instrument Panel Cluster Control Module (Combination Meter) | The clearance warning ECU assembly does not receive data from the combination meter assembly for 6.5 seconds or more. | Both conditions are met:
| Turn the power switch on (IG) and wait at least 8.5 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
| DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF V BUS, PAST COMMUNICATION ERROR) |
Regarding the past communication error of ECUs and sensors connected to the V bus (in this case, normal was displayed when performing the communication bus check, but communication DTCs are output), the probable CAN branch that had a malfunction can be determined based on the following DTC combination table.
| V Bus (Open in one CAN branch line) | |||||||
| Trouble Mode | |||||||
| Output ECU | Output DTC | Center Airbag Sensor Communication Stop Mode (Click here) | Air Conditioning Amplifier Communication Stop Mode (Click here) | Audio Receiver Assembly Communication Stop Mode (Click here) | Main Body ECU Communication Stop Mode (Click here) | Skid Control ECU Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | ○ | - | - | - | |
| U0142 | - | ○ | - | ○ | - | ||
| U0155 | - | ○ | - | - | - | ||
| U0293 | - | ○ | - | - | - | ||
| Radio and Display Receiver Assembly | U0073 | - | - | ○ | - | - | |
| U0100 | - | - | ○ | - | - | ||
| U0129 | X | X | ○ | X | ○ | ||
| U0140 | - | - | ○ | ○ | - | ||
| U0155 | - | - | ○ | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| Multiplex Network Body ECU | U0100 | - | - | - | ○ | - | |
| U0101 | - | - | - | ○ | - | ||
| U0120 | - | - | - | ○ | - | ||
| U0151 | ○ | - | - | ○ | - | ||
| U0155 | - | - | - | ○ | - | ||
| U0164 | - | ○ | - | ○ | - | ||
| U0293 | - | - | - | ○ | - | ||
| U0327 | - | - | - | ○ | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | ○ | |
| U0123 | ○ | ○ | ○ | ○ | ○ | ||
| U0124 | ○ | ○ | ○ | ○ | ○ | ||
| U0126 | ○ | ○ | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ○ | ○ | ||
| Power Steering ECU Assembly | U0129 | - | - | - | - | ○ | |
| U0293 | - | - | - | - | - | ||
| ECM | - | - | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | - | - | |
| U0142 | - | - | - | ○ | - | ||
| U0155 | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | - | |
| U0129 | - | - | - | - | ○ | ||
| U0131 | - | - | - | - | - | ||
| U0142 | - | - | - | ○ | - | ||
| U0151 | ○ | - | - | - | - | ||
| V Bus | Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - |
| U0129 | - | - | - | - | ○ | ||
| U0140 | - | - | - | ○ | - | ||
| U0151 | ○ | - | - | - | - | ||
| U0164 | - | ○ | - | - | - | ||
| U1107 | - | - | - | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | - | ○ | - | |
| U0155 | - | - | - | - | - | ||
| U0293 | - | X | X | X | X | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | ○ | |
| Steering Sensor | - | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | - | - | - |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | |
| U0123 | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | |
| U0129 | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | |
| V Bus (Open in one CAN branch line) | |||||||
| Trouble Mode | |||||||
| Output ECU | Output DTC | Power Steering ECU Communication Stop Mode (Click here) | Certification ECU Communication Stop Mode (Click here) | Power Management Control ECU Communication Stop Mode (Click here) | Steering Angle Sensor Communication Stop Mode (Click here) | DLC3 | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - | - |
| V Bus | Air Conditioning Amplifier Assembly | U0131 | ○ | - | - | - | - |
| U0142 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| Radio and Display Receiver Assembly | U0073 | - | - | - | - | - | |
| U0100 | - | - | - | - | - | ||
| U0129 | X | X | X | X | X | ||
| U0140 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| Multiplex Network Body ECU | U0100 | - | - | - | - | - | |
| U0101 | - | - | ○ | - | - | ||
| U0120 | - | - | ○ | - | - | ||
| U0151 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| U0327 | - | ○ | - | - | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | |
| U0123 | ○ | ○ | ○ | ○ | ○ | ||
| U0124 | ○ | ○ | ○ | ○ | ○ | ||
| U0126 | ○ | ○ | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ○ | ○ | ||
| Power Steering ECU Assembly | U0129 | ○ | - | - | - | - | |
| U0293 | ○ | - | ○ | - | - | ||
| ECM | - | - | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | ○ | - | - | - | |
| U0142 | - | ○ | - | - | - | ||
| U0155 | - | ○ | - | - | - | ||
| U0293 | - | ○ | ○ | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | - | |
| U0129 | - | - | - | - | - | ||
| U0131 | ○ | - | - | - | - | ||
| U0142 | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | ○ | - | - | |
| U0129 | - | - | ○ | - | - | ||
| U0140 | - | - | ○ | - | - | ||
| U0151 | - | - | ○ | - | - | ||
| U0164 | - | - | ○ | - | - | ||
| U1107 | - | - | ○ | - | - | ||
| V Bus | Power Management Control ECU (Power Management CPU) | U0140 | - | - | ○ | - | - |
| U0155 | - | - | ○ | - | - | ||
| U0293 | - | X | ○ | X | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | ○ | - | - | |
| Steering Sensor | - | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | - | - | - |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | |
| U0123 | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | |
| U0129 | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | |
| V Bus (Open in both CAN branch lines) | |||||||
| Trouble Mode | |||||||
| Output ECU | Output DTC | Center Airbag Sensor Communication Stop Mode (Click here) | Air Conditioning Amplifier Communication Stop Mode (Click here) | Audio Receiver Assembly Communication Stop Mode (Click here) | Main Body ECU Communication Stop Mode (Click here) | Skid Control ECU Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - | - |
| V Bus | Air Conditioning Amplifier Assembly | U0131 | - | ○ | - | - | - |
| U0142 | - | ○ | - | ○ | - | ||
| U0155 | - | ○ | - | - | - | ||
| U0293 | - | ○ | - | - | - | ||
| Radio and Display Receiver Assembly | U0073 | - | - | ○ | - | - | |
| U0100 | - | - | ○ | - | - | ||
| U0129 | - | - | ○ | - | ○ | ||
| U0140 | - | - | ○ | ○ | - | ||
| U0155 | - | - | ○ | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| Multiplex Network Body ECU | U0100 | - | - | - | ○ | - | |
| U0101 | - | - | - | ○ | - | ||
| U0120 | - | - | - | ○ | - | ||
| U0151 | ○ | - | - | ○ | - | ||
| U0155 | - | - | - | ○ | - | ||
| U0164 | - | ○ | - | ○ | - | ||
| U0293 | - | - | - | ○ | - | ||
| U0327 | - | - | - | ○ | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | ○ | |
| U0123 | ○ | - | - | - | ○ | ||
| U0124 | ○ | - | - | - | ○ | ||
| U0126 | - | - | - | - | ○ | ||
| U0293 | - | - | - | - | ○ | ||
| Power Steering ECU Assembly | U0129 | - | - | - | - | ○ | |
| U0293 | - | - | - | - | - | ||
| ECM | - | - | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | - | - | |
| U0142 | - | - | - | ○ | - | ||
| U0155 | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | - | |
| U0129 | - | - | - | - | ○ | ||
| U0131 | - | - | - | - | - | ||
| U0142 | - | - | - | ○ | - | ||
| U0151 | ○ | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | |
| U0129 | - | - | - | - | ○ | ||
| U0140 | - | - | - | ○ | - | ||
| U0151 | ○ | - | - | - | - | ||
| U0164 | - | ○ | - | - | - | ||
| U1107 | - | - | - | - | - | ||
| V Bus | Power Management Control ECU (Power Management CPU) | U0140 | - | - | - | ○ | - |
| U0155 | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | ○ | |
| Steering Sensor | - | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | - | - | - |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | |
| U0123 | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | |
| U0129 | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | |
| V Bus (Open in both CAN branch lines) | |||||||
| Trouble Mode | |||||||
| Output ECU | Output DTC | Power Steering ECU Communication Stop Mode (Click here) | Certification ECU Communication Stop Mode (Click here) | Power Management Control ECU Communication Stop Mode (Click here) | Steering Angle Sensor Communication Stop Mode (Click here) | DLC3 | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | ○ | - | - | - | - | |
| U0142 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| V Bus | Radio and Display Receiver Assembly | U0073 | - | - | - | - | - |
| U0100 | - | - | - | - | - | ||
| U0129 | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| Multiplex Network Body ECU | U0100 | - | - | - | - | - | |
| U0101 | - | - | ○ | - | - | ||
| U0120 | - | - | ○ | - | - | ||
| U0151 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| U0327 | - | ○ | - | - | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | |
| U0123 | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | ||
| U0126 | - | - | - | ○ | - | ||
| U0293 | - | - | ○ | - | - | ||
| Power Steering ECU Assembly | U0129 | ○ | - | - | - | - | |
| U0293 | ○ | - | ○ | - | - | ||
| ECM | - | - | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | ○ | - | - | - | |
| U0142 | - | ○ | - | - | - | ||
| U0155 | - | ○ | - | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | - | |
| U0129 | - | - | - | - | - | ||
| U0131 | ○ | - | - | - | - | ||
| U0142 | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | ○ | - | - | |
| U0129 | - | - | ○ | - | - | ||
| U0140 | - | - | ○ | - | - | ||
| U0151 | - | - | ○ | - | - | ||
| U0164 | - | - | ○ | - | - | ||
| U1107 | - | - | ○ | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | ○ | - | - | |
| U0155 | - | - | ○ | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| V Bus | Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | ○ | - | - |
| Steering Sensor | - | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | - | - | - |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | |
| U0123 | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | |
| U0129 | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | |
| V Bus (Open in one CAN main bus line) | V Bus (Open in both CAN main bus lines) | |||||||
| Trouble Mode | Trouble Mode | |||||||
| Output ECU | Output DTC | Combination Meter ECU Communication Stop Mode (Click here) | CAN J/C LH to CAN J/C RH | ECM Communication Stop Mode (Click here) | Combination Meter ECU Communication Stop Mode (Click here) | CAN J/C LH to CAN J/C RH | ECM Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | - | - | - | - | - | |
| U0142 | - | ○ | - | - | ○ | - | ||
| U0155 | ○ | ○ | - | ○ | ○ | - | ||
| U0293 | - | - | - | - | - | - | ||
| V Bus | Radio and Display Receiver Assembly | U0073 | - | - | - | - | - | - |
| U0100 | - | ○ | ○ | - | ○ | ○ | ||
| U0129 | X | ○ | X | - | ○ | - | ||
| U0140 | - | ○ | - | - | ○ | - | ||
| U0155 | ○ | ○ | - | ○ | ○ | - | ||
| U0293 | - | ○ | - | - | ○ | - | ||
| Multiplex Network Body ECU | U0100 | - | - | ○ | - | - | ○ | |
| U0101 | - | - | - | - | - | - | ||
| U0120 | - | - | - | - | - | - | ||
| U0151 | - | ○ | - | - | ○ | - | ||
| U0155 | ○ | - | - | ○ | - | - | ||
| U0164 | - | ○ | - | - | ○ | - | ||
| U0293 | - | - | - | - | - | - | ||
| U0327 | - | ○ | - | - | ○ | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | - | |
| U0123 | ○ | ○ | ○ | - | ○ | - | ||
| U0124 | ○ | ○ | ○ | - | ○ | - | ||
| U0126 | ○ | ○ | ○ | - | - | - | ||
| U0293 | ○ | ○ | ○ | - | - | - | ||
| Power Steering ECU Assembly | U0129 | - | ○ | - | - | ○ | - | |
| U0293 | - | ○ | - | - | ○ | - | ||
| ECM | - | - | - | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | ○ | - | - | ○ | |
| U0142 | - | ○ | - | - | ○ | - | ||
| U0155 | ○ | ○ | - | ○ | ○ | - | ||
| U0293 | - | ○ | - | - | ○ | - | ||
| Combination Meter Assembly | U0100 | ○ | - | ○ | ○ | - | ○ | |
| U0129 | ○ | - | - | ○ | - | - | ||
| U0131 | ○ | ○ | - | ○ | ○ | - | ||
| U0142 | ○ | - | - | ○ | - | - | ||
| U0151 | ○ | ○ | - | ○ | ○ | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | ○ | ○ | - | ○ | ○ | |
| U0129 | - | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | - | ||
| U0151 | - | ○ | - | - | ○ | - | ||
| U0164 | - | ○ | - | - | ○ | - | ||
| U1107 | - | - | - | - | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | - | - | - | - | |
| U0155 | ○ | - | - | ○ | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| V Bus | Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | - |
| Steering Sensor | - | - | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | - | - | - | - |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | - | |
| U0123 | - | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | - | |
| U0129 | - | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | - | |
| V Bus (CAN bus line short circuit) | V Bus (CAN bus line short to GND) | ||||
| Trouble Mode | Trouble Mode | ||||
| Output ECU | Output DTC | CANH to CANL | CANH to GND | CANL to GND | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | ○ | ○ | ○ | |
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ||
| V Bus | Radio and Display Receiver Assembly | U0073 | ○ | ○ | ○ |
| U0100 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0140 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ||
| Multiplex Network Body ECU | U0100 | ○ | ○ | ○ | |
| U0101 | ○ | ○ | ○ | ||
| U0120 | ○ | ○ | ○ | ||
| U0151 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| U0164 | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ||
| U0327 | ○ | ○ | ○ | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | ○ | ○ | ○ | |
| U0123 | ○ | ○ | ○ | ||
| U0124 | ○ | ○ | ○ | ||
| U0126 | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ||
| Power Steering ECU Assembly | U0129 | ○ | ○ | ○ | |
| U0293 | ○ | ○ | ○ | ||
| ECM | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | ○ | ○ | ○ | |
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ||
| Combination Meter Assembly | U0100 | ○ | ○ | ○ | |
| U0129 | ○ | ○ | ○ | ||
| U0131 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0151 | ○ | ○ | ○ | ||
| Power Management Control ECU (HV CPU) | U0100 | ○ | ○ | ○ | |
| U0129 | ○ | ○ | ○ | ||
| U0140 | ○ | ○ | ○ | ||
| U0151 | ○ | ○ | ○ | ||
| U0164 | ○ | ○ | ○ | ||
| U1107 | ○ | ○ | ○ | ||
| Power Management Control ECU (Power Management CPU) | U0140 | ○ | ○ | ○ | |
| U0155 | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | ○ | ○ | ○ | |
| Steering Sensor | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | - |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | |
| U0123 | - | - | - | ||
| U0124 | - | - | - | ||
| U0126 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0151 | - | - | - | ||
| U0164 | - | - | - | ||
| U1107 | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | |
| V Bus (Open in one CAN branch line) | ||||||||
| Trouble Mode | ||||||||
| Output ECU | Output DTC | Center Airbag Sensor Communication Stop Mode (Click here) | Air Conditioning Amplifier Communication Stop Mode (Click here) | Audio Receiver Assembly Communication Stop Mode (Click here) | Main Body ECU Communication Stop Mode (Click here) | Clearance Warning ECU Communication Stop Mode (Click here) | Skid Control ECU Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | ○ | - | - | - | - | |
| U0142 | - | ○ | - | ○ | - | - | ||
| U0155 | - | ○ | - | - | - | - | ||
| U0293 | - | ○ | - | - | - | - | ||
| Radio and Display Receiver Assembly | U0073 | - | - | ○ | - | - | - | |
| U0100 | - | - | ○ | - | - | - | ||
| U0129 | X | X | ○ | X | X | ○ | ||
| U0140 | - | - | ○ | ○ | - | - | ||
| U0155 | - | - | ○ | - | - | - | ||
| U0293 | - | - | ○ | - | - | - | ||
| V Bus | Multiplex Network Body ECU | U0100 | - | - | - | ○ | - | - |
| U0101 | - | - | - | ○ | - | - | ||
| U0120 | - | - | - | ○ | - | - | ||
| U0151 | ○ | - | - | ○ | - | - | ||
| U0155 | - | - | - | ○ | - | - | ||
| U0164 | - | ○ | - | ○ | - | - | ||
| U0293 | - | - | - | ○ | - | - | ||
| U0327 | - | - | - | ○ | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | - | - | ○ | - | |
| U0101 | - | - | - | - | ○ | - | ||
| U0142 | - | - | - | ○ | ○ | - | ||
| U0155 | - | - | - | - | ○ | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | ○ | |
| U0123 | ○ | ○ | ○ | ○ | ○ | ○ | ||
| U0124 | ○ | ○ | ○ | ○ | ○ | ○ | ||
| U0126 | ○ | ○ | ○ | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ○ | ○ | ○ | ||
| Power Steering ECU Assembly | U0129 | - | - | - | - | - | ○ | |
| U0293 | - | - | - | - | - | - | ||
| ECM | - | - | - | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | - | - | - | |
| U0142 | - | - | - | ○ | - | - | ||
| U0155 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | - | - | |
| U0129 | - | - | - | - | - | ○ | ||
| U0131 | - | - | - | - | - | - | ||
| U0142 | - | - | - | ○ | - | - | ||
| U0151 | ○ | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | - | |
| U0129 | - | - | - | - | - | ○ | ||
| U0140 | - | - | - | ○ | - | - | ||
| U0151 | ○ | - | - | - | - | - | ||
| U0164 | - | ○ | - | - | - | - | ||
| U1107 | - | - | - | - | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | - | ○ | - | - | |
| U0155 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| V Bus | Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | ○ |
| Steering Sensor | - | - | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | - | - | - | - |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | - | |
| U0123 | - | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | - | |
| U0129 | - | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | - | |
| V Bus (Open in one CAN branch line) | |||||||
| Trouble Mode | |||||||
| Output ECU | Output DTC | Power Steering ECU Communication Stop Mode (Click here) | Certification ECU Communication Stop Mode (Click here) | Power Management Control ECU Communication Stop Mode (Click here) | Steering Angle Sensor Communication Stop Mode (Click here) | DLC3 | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | ○ | - | - | - | - | |
| U0142 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| Radio and Display Receiver Assembly | U0073 | - | - | - | - | - | |
| U0100 | - | - | - | - | - | ||
| U0129 | X | X | X | X | X | ||
| U0140 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | ||
| V Bus | Multiplex Network Body ECU | U0100 | - | - | - | - | - |
| U0101 | - | - | ○ | - | - | ||
| U0120 | - | - | ○ | - | - | ||
| U0151 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | ||
| U0327 | - | ○ | - | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | - | - | - | |
| U0101 | - | - | - | - | - | ||
| U0142 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | |
| U0123 | ○ | ○ | ○ | ○ | ○ | ||
| U0124 | ○ | ○ | ○ | ○ | ○ | ||
| U0126 | ○ | ○ | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ○ | ○ | ||
| Power Steering ECU Assembly | U0129 | ○ | - | - | - | - | |
| U0293 | ○ | - | ○ | - | - | ||
| ECM | - | - | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | ○ | - | - | - | |
| U0142 | - | ○ | - | - | - | ||
| U0155 | - | ○ | - | - | - | ||
| U0293 | - | ○ | ○ | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | - | |
| U0129 | - | - | - | - | - | ||
| U0131 | ○ | - | - | - | - | ||
| U0142 | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | ○ | - | - | |
| U0129 | - | - | ○ | - | - | ||
| U0140 | - | - | ○ | - | - | ||
| U0151 | - | - | ○ | - | - | ||
| U0164 | - | - | ○ | - | - | ||
| U1107 | - | - | ○ | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | ○ | - | - | |
| U0155 | - | - | ○ | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| V Bus | Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | ○ | - | - |
| Steering Sensor | - | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | - | - | - |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | |
| U0123 | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | |
| U0129 | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | |
| V Bus (Open in both CAN branch lines) | ||||||||
| Trouble Mode | ||||||||
| Output ECU | Output DTC | Center Airbag Sensor Communication Stop Mode (Click here) | Air Conditioning Amplifier Communication Stop Mode (Click here
| Audio Receiver Assembly Communication Stop Mode (Click here) | Main Body ECU Communication Stop Mode (Click here) | Clearance Warning ECU Communication Stop Mode (Click here) | Skid Control ECU Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | ○ | - | - | - | - | |
| U0142 | - | ○ | - | ○ | - | - | ||
| U0155 | - | ○ | - | - | - | - | ||
| U0293 | - | ○ | - | - | - | - | ||
| V Bus | Radio and Display Receiver Assembly | U0073 | - | - | ○ | - | - | - |
| U0100 | - | - | ○ | - | - | - | ||
| U0129 | - | - | ○ | - | - | ○ | ||
| U0140 | - | - | ○ | ○ | - | - | ||
| U0155 | - | - | ○ | - | - | - | ||
| U0293 | - | - | ○ | - | - | - | ||
| Multiplex Network Body ECU | U0100 | - | - | - | ○ | - | - | |
| U0101 | - | - | - | ○ | - | - | ||
| U0120 | - | - | - | ○ | - | - | ||
| U0151 | ○ | - | - | ○ | - | - | ||
| U0155 | - | - | - | ○ | - | - | ||
| U0164 | - | ○ | - | ○ | - | - | ||
| U0293 | - | - | - | ○ | - | - | ||
| U0327 | - | - | - | ○ | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | - | - | ○ | - | |
| U0101 | - | - | - | - | ○ | - | ||
| U0142 | - | - | - | ○ | ○ | - | ||
| U0155 | - | - | - | - | ○ | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | ○ | |
| U0123 | ○ | - | - | - | - | ○ | ||
| U0124 | ○ | - | - | - | - | ○ | ||
| U0126 | - | - | - | - | - | ○ | ||
| U0293 | - | - | - | - | - | ○ | ||
| Power Steering ECU Assembly | U0129 | - | - | - | - | - | ○ | |
| U0293 | - | - | - | - | - | - | ||
| ECM | - | - | - | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | - | - | - | |
| U0142 | - | - | - | ○ | - | - | ||
| U0155 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | - | - | |
| U0129 | - | - | - | - | - | ○ | ||
| U0131 | - | - | - | - | - | - | ||
| U0142 | - | - | - | ○ | - | - | ||
| U0151 | ○ | - | - | - | - | - | ||
| V Bus | Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | - |
| U0129 | - | - | - | - | - | ○ | ||
| U0140 | - | - | - | ○ | - | - | ||
| U0151 | ○ | - | - | - | - | - | ||
| U0164 | - | ○ | - | - | - | - | ||
| U1107 | - | - | - | - | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | - | ○ | - | - | |
| U0155 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | ○ | |
| Steering Sensor | - | - | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | - | - | - | - |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | - | |
| U0123 | - | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | - | |
| U0129 | - | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | - | |
| V Bus (Open in both CAN branch lines) | |||||||
| Trouble Mode | |||||||
| Output ECU | Output DTC | Power Steering ECU Communication Stop Mode (Click here) | Certification ECU Communication Stop Mode (Click here) | Power Management Control ECU Communication Stop Mode (Click here) | Steering Angle Sensor Communication Stop Mode (Click here) | DLC3 | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - | - |
| V Bus | Air Conditioning Amplifier Assembly | U0131 | ○ | - | - | - | - |
| U0142 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| Radio and Display Receiver Assembly | U0073 | - | - | - | - | - | |
| U0100 | - | - | - | - | - | ||
| U0129 | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| Multiplex Network Body ECU | U0100 | - | - | - | - | - | |
| U0101 | - | - | ○ | - | - | ||
| U0120 | - | - | ○ | - | - | ||
| U0151 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| U0327 | - | ○ | - | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | - | - | - | |
| U0101 | - | - | - | - | - | ||
| U0142 | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | |
| U0123 | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | ||
| U0126 | - | - | - | ○ | - | ||
| U0293 | - | - | - | - | - | ||
| Power Steering ECU Assembly | U0129 | ○ | - | - | - | - | |
| U0293 | ○ | - | ○ | - | - | ||
| ECM | - | - | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | ○ | - | - | - | |
| U0142 | - | ○ | - | - | - | ||
| U0155 | - | ○ | - | - | - | ||
| U0293 | - | ○ | ○ | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | - | |
| U0129 | - | - | - | - | - | ||
| U0131 | ○ | - | - | - | - | ||
| U0142 | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | ||
| V Bus | Power Management Control ECU (HV CPU) | U0100 | - | - | ○ | - | - |
| U0129 | - | - | ○ | - | - | ||
| U0140 | - | - | ○ | - | - | ||
| U0151 | - | - | ○ | - | - | ||
| U0164 | - | - | ○ | - | - | ||
| U1107 | - | - | ○ | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | ○ | - | - | |
| U0155 | - | - | ○ | - | - | ||
| U0293 | - | - | ○ | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | ○ | - | - | |
| Steering Sensor | - | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | - | - | - |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | |
| U0123 | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | |
| U0129 | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | |
| V Bus (Open in one CAN main bus line) | V Bus (Open in both CAN main bus lines) | |||||||
| Trouble Mode | Trouble Mode | |||||||
| Output ECU | Output DTC | Combination Meter ECU Communication Stop Mode (Click here) | CAN J/C LH to CAN J/C RH | ECM Communication Stop Mode (Click here) | Combination Meter ECU Communication Stop Mode (Click here) | CAN J/C LH to CAN J/C RH | ECM Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | - | - | - | - | - | |
| U0142 | - | - | - | - | - | - | ||
| U0155 | ○ | ○ | - | ○ | ○ | - | ||
| U0293 | - | - | - | - | - | - | ||
| Radio and Display Receiver Assembly | U0073 | - | - | - | - | - | - | |
| U0100 | - | - | ○ | - | - | ○ | ||
| U0129 | X | ○ | X | - | ○ | - | ||
| U0140 | - | - | - | - | - | - | ||
| U0155 | ○ | ○ | - | ○ | ○ | - | ||
| U0293 | - | - | - | - | - | - | ||
| Multiplex Network Body ECU | U0100 | - | - | ○ | - | - | ○ | |
| U0101 | - | - | - | - | - | - | ||
| U0120 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| U0155 | ○ | ○ | - | ○ | ○ | - | ||
| U0164 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| U0327 | - | ○ | - | - | ○ | - | ||
| Clearance Warning ECU Assembly | U0100 | - | ○ | ○ | - | ○ | ○ | |
| U0101 | - | ○ | ○ | - | ○ | ○ | ||
| U0142 | - | ○ | - | - | ○ | - | ||
| U0155 | ○ | - | - | ○ | - | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | - | |
| U0123 | ○ | ○ | ○ | - | ○ | - | ||
| U0124 | ○ | ○ | ○ | - | ○ | - | ||
| U0126 | ○ | ○ | ○ | - | - | - | ||
| U0293 | ○ | ○ | ○ | - | ○ | - | ||
| Power Steering ECU Assembly | U0129 | - | ○ | X | - | ○ | - | |
| U0293 | - | - | - | - | - | - | ||
| ECM | - | - | - | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | ○ | ○ | - | ○ | ○ | |
| U0142 | - | ○ | - | - | ○ | - | ||
| U0155 | ○ | - | - | ○ | - | - | ||
| U0293 | - | ○ | - | - | ○ | - | ||
| Combination Meter Assembly | U0100 | ○ | ○ | ○ | ○ | ○ | ○ | |
| U0129 | ○ | - | X | ○ | - | - | ||
| U0131 | ○ | ○ | - | ○ | ○ | - | ||
| U0142 | ○ | ○ | - | ○ | ○ | - | ||
| U0151 | ○ | ○ | - | ○ | ○ | - | ||
| V Bus | Power Management Control ECU (HV CPU) | U0100 | - | - | ○ | - | - | ○ |
| U0129 | - | ○ | - | - | ○ | - | ||
| U0140 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | - | - | - | - | |
| U0155 | ○ | ○ | - | ○ | ○ | - | ||
| U0293 | X | - | X | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | ○ | X | - | ○ | - | |
| Steering Sensor | - | - | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | - | - | - | - |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | - | |
| U0123 | - | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | - | |
| U0129 | - | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | - | |
| V Bus (CAN bus line short circuit) | V Bus (CAN bus line short to GND) | ||||
| Trouble Mode | Trouble Mode | ||||
| Output ECU | Output DTC | CANH to CANL | CANH to GND | CANL to GND | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | ○ | ○ | ○ | |
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ||
| Radio and Display Receiver Assembly | U0073 | ○ | ○ | ○ | |
| U0100 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0140 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ||
| Multiplex Network Body ECU | U0100 | ○ | ○ | ○ | |
| U0101 | ○ | ○ | ○ | ||
| U0120 | ○ | ○ | ○ | ||
| U0151 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| U0164 | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ||
| U0327 | ○ | ○ | ○ | ||
| Clearance Warning ECU Assembly | U0100 | ○ | ○ | ○ | |
| U0101 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | ○ | ○ | ○ | |
| U0123 | ○ | ○ | ○ | ||
| U0124 | ○ | ○ | ○ | ||
| U0126 | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ||
| Power Steering ECU Assembly | U0129 | ○ | ○ | ○ | |
| U0293 | ○ | ○ | ○ | ||
| ECM | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | ○ | ○ | ○ | |
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ||
| Combination Meter Assembly | U0100 | ○ | ○ | ○ | |
| U0129 | ○ | ○ | ○ | ||
| U0131 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0151 | ○ | ○ | ○ | ||
| V Bus | Power Management Control ECU (HV CPU) | U0100 | ○ | ○ | ○ |
| U0129 | ○ | ○ | ○ | ||
| U0140 | ○ | ○ | ○ | ||
| U0151 | ○ | ○ | ○ | ||
| U0164 | ○ | ○ | ○ | ||
| U1107 | ○ | ○ | ○ | ||
| Power Management Control ECU (Power Management CPU) | U0140 | ○ | ○ | ○ | |
| U0155 | ○ | ○ | ○ | ||
| U0293 | ○ | ○ | ○ | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | ○ | ○ | ○ | |
| Steering Sensor | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | - |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | |
| U0123 | - | - | - | ||
| U0124 | - | - | - | ||
| U0126 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0151 | - | - | - | ||
| U0164 | - | - | - | ||
| U1107 | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | |
| DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF SUB BUS 15, PAST COMMUNICATION ERROR) |
Regarding the past communication error of ECUs connected to the sub bus 15 (in this case, normal was displayed when performing the communication bus check, but communication DTCs are output), the probable CAN branch that had a malfunction can be determined based on the following DTC combination table.
| Sub Bus 15 (Open in one CAN branch line) | Sub Bus 15 (Open in both CAN branch lines) | Sub Bus 15 (Open in one CAN main bus line) | ||||||
| Trouble Mode | Trouble Mode | Trouble Mode | ||||||
| Output ECU | Output DTC | Brake Booster with Master Cylinder Assembly (Skid Control ECU) | Brake Booster with Master Cylinder Assembly (Skid Control ECU) | Power Management Control ECU (HV CPU) | CAN No. 1 J/C to Power Management Control ECU (HV CPU) | CAN No. 1 J/C to ECM | ECM | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | - | - | - | - | - | |
| U0142 | - | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Radio and Display Receiver Assembly | U0073 | - | - | - | - | - | - | |
| U0100 | - | - | - | - | - | - | ||
| U0129 | - | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Multiplex Network Body ECU | U0100 | - | - | - | - | - | - | |
| U0101 | - | - | - | - | - | - | ||
| U0120 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| U0327 | - | - | - | - | - | - | ||
| V Bus | Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | - |
| U0123 | - | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Power Steering ECU Assembly | U0129 | - | - | - | - | - | - | |
| U0293 | - | - | - | - | - | - | ||
| ECM | - | - | - | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | - | - | - | |
| U0142 | - | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | - | - | |
| U0129 | - | - | - | - | - | - | ||
| U0131 | - | - | - | - | - | - | ||
| U0142 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | - | |
| U0129 | - | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | - | - | - | - | |
| U0155 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | - | |
| Steering Sensor | - | - | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | ○ | ○ | ○ | ○ |
| Sub Bus 15 | Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | ○ | ○ | - | - | - | - |
| U0123 | - | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | ○ | ○ | ○ | ○ | |
| U0129 | ○ | ○ | ○ | - | - | - | ||
| U0140 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | - | ||
| U1107 | - | - | ○ | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | - | |
| Sub Bus 15 (Open in both CAN main bus lines) | ||||||
| Trouble Mode | ||||||
| Output ECU | Output DTC | Power Management Control ECU (HV CPU) | CAN No. 1 J/C to Power Management Control ECU (HV CPU) | CAN No. 1 J/C to ECM | ECM | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | - | - | - | |
| U0142 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| Radio and Display Receiver Assembly | U0073 | - | - | - | - | |
| U0100 | - | - | - | - | ||
| U0129 | - | - | - | - | ||
| U0140 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| V Bus | Multiplex Network Body ECU | U0100 | - | - | - | - |
| U0101 | - | - | - | - | ||
| U0120 | - | - | - | - | ||
| U0151 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| U0164 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| U0327 | - | - | - | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | |
| U0123 | - | - | - | - | ||
| U0124 | - | - | - | - | ||
| U0126 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| Power Steering ECU Assembly | U0129 | - | - | - | - | |
| U0293 | - | - | - | - | ||
| ECM | - | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | - | |
| U0142 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | |
| U0129 | - | - | - | - | ||
| U0131 | - | - | - | - | ||
| U0142 | - | - | - | - | ||
| U0151 | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | |
| U0129 | - | - | - | - | ||
| U0140 | - | - | - | - | ||
| U0151 | - | - | - | - | ||
| U0164 | - | - | - | - | ||
| U1107 | - | - | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | - | - | |
| U0155 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | |
| Steering Sensor | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | ○ | ○ | ○ | ○ |
| Sub Bus 15 | Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - |
| U0123 | - | - | - | - | ||
| U0124 | - | - | - | - | ||
| U0126 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | ○ | ○ | ○ | ○ | |
| U0129 | ○ | - | - | - | ||
| U0140 | - | - | - | - | ||
| U0151 | - | - | - | - | ||
| U0164 | - | - | - | - | ||
| U1107 | ○ | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | |
| Sub Bus 15 (CAN bus line short circuit) | Sub Bus 15 (CAN bus line short to GND) | ||||
| Trouble Mode | Trouble Mode | ||||
| Output ECU | Output DTC | CANH to CANL | CANH to GND | CANL to GND | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | - | - | |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Radio and Display Receiver Assembly | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Multiplex Network Body ECU | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U0293 | - | - | - | ||
| U0327 | - | - | - | ||
| V Bus | Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - |
| U0123 | - | - | - | ||
| U0124 | - | - | - | ||
| U0126 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Steering ECU Assembly | U0129 | - | - | - | |
| U0293 | - | - | - | ||
| ECM | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0151 | - | - | - | ||
| U0164 | - | - | - | ||
| U1107 | - | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | - | |
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | |
| Steering Sensor | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | ○ | ○ | ○ |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | ○ | ○ | ○ | |
| U0123 | - | - | - | ||
| U0124 | - | - | - | ||
| U0126 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | ○ | ○ | ○ | |
| U0129 | ○ | ○ | ○ | ||
| U0140 | - | - | - | ||
| U0151 | - | - | - | ||
| U0164 | - | - | - | ||
| U1107 | ○ | ○ | ○ | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | |
| Sub Bus 15 (Open in one CAN branch line) | Sub Bus 15 (Open in both CAN branch lines) | Sub Bus 15 (Open in one CAN main bus line) | ||||||
| Trouble Mode | Trouble Mode | Trouble Mode | ||||||
| Output ECU | Output DTC | Brake Booster with Master Cylinder Assembly (Skid Control ECU) | Brake Booster with Master Cylinder Assembly (Skid Control ECU) | Power Management Control ECU (HV CPU) | CAN No. 1 J/C to Power Management Control ECU (HV CPU) | CAN No. 1 J/C to ECM | ECM | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | - | - | - | - | - | |
| U0142 | - | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Radio and Display Receiver Assembly | U0073 | - | - | - | - | - | - | |
| U0100 | - | - | - | - | - | - | ||
| U0129 | - | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Multiplex Network Body ECU | U0100 | - | - | - | - | - | - | |
| U0101 | - | - | - | - | - | - | ||
| U0120 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| U0327 | - | - | - | - | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | - | - | - | - | |
| U0101 | - | - | - | - | - | - | ||
| U0142 | - | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | - | - | |
| U0123 | - | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Power Steering ECU Assembly | U0129 | - | - | - | - | - | - | |
| U0293 | - | - | - | - | - | - | ||
| ECM | - | - | - | - | - | - | - | |
| V Bus | Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | - | - | - |
| U0142 | - | - | - | - | - | - | ||
| U0155 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | - | - | |
| U0129 | - | - | - | - | - | - | ||
| U0131 | - | - | - | - | - | - | ||
| U0142 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | - | - | |
| U0129 | - | - | - | - | - | - | ||
| U0140 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | - | - | - | - | |
| U0155 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | - | |
| Steering Sensor | - | - | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | - | - | ○ | ○ | ○ | ○ |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | ○ | ○ | - | - | - | - | |
| U0123 | - | - | - | - | - | - | ||
| U0124 | - | - | - | - | - | - | ||
| U0126 | - | - | - | - | - | - | ||
| U0293 | - | - | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | ○ | ○ | ○ | ○ | |
| U0129 | ○ | ○ | - | - | - | - | ||
| U0140 | - | - | - | - | - | - | ||
| U0151 | - | - | - | - | - | - | ||
| U0164 | - | - | - | - | - | - | ||
| U1107 | - | - | - | - | - | - | ||
| Sub Bus 15 | Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | - | - |
| Sub Bus 15 (Open in both CAN main bus lines) | ||||||
| Trouble Mode | ||||||
| Output ECU | Output DTC | Power Management Control ECU (HV CPU) | CAN No. 1 J/C to Power Management Control ECU (HV CPU) | CAN No. 1 J/C to ECM | ECM | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | - | - | - | |
| U0142 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| Radio and Display Receiver Assembly | U0073 | - | - | - | - | |
| U0100 | - | - | - | - | ||
| U0129 | - | - | - | - | ||
| U0140 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| Multiplex Network Body ECU | U0100 | - | - | - | - | |
| U0101 | - | - | - | - | ||
| U0120 | - | - | - | - | ||
| U0151 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| U0164 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| U0327 | - | - | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | - | - | |
| U0101 | - | - | - | - | ||
| U0142 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| V Bus | Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - |
| U0123 | - | - | - | - | ||
| U0124 | - | - | - | - | ||
| U0126 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| Power Steering ECU Assembly | U0129 | - | - | - | - | |
| U0293 | - | - | - | - | ||
| ECM | - | - | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | - | |
| U0142 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | |
| U0129 | - | - | - | - | ||
| U0131 | - | - | - | - | ||
| U0142 | - | - | - | - | ||
| U0151 | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | - | |
| U0129 | - | - | - | - | ||
| U0140 | - | - | - | - | ||
| U0151 | - | - | - | - | ||
| U0164 | - | - | - | - | ||
| U1107 | - | - | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | - | - | |
| U0155 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - | |
| Steering Sensor | - | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | ○ | ○ | ○ | ○ |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | - | |
| U0123 | - | - | - | - | ||
| U0124 | - | - | - | - | ||
| U0126 | - | - | - | - | ||
| U0293 | - | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | ○ | ○ | ○ | ○ | |
| U0129 | ○ | - | - | - | ||
| U0140 | - | - | - | - | ||
| U0151 | - | - | - | - | ||
| U0164 | - | - | - | - | ||
| U1107 | ○ | - | - | - | ||
| Sub Bus 15 | Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | - |
| Sub Bus 15 (CAN bus line short circuit) | Sub Bus 15 (CAN bus line short to GND) | ||||
| Trouble Mode | Trouble Mode | ||||
| Output ECU | Output DTC | CANH to CANL | CANH to GND | CANL to GND | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | - | - | |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Radio and Display Receiver Assembly | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Multiplex Network Body ECU | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U0293 | - | - | - | ||
| U0327 | - | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | |
| U0123 | - | - | - | ||
| U0124 | - | - | - | ||
| U0126 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Steering ECU Assembly | U0129 | - | - | - | |
| U0293 | - | - | - | ||
| ECM | - | - | - | - | |
| V Bus | Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0151 | - | - | - | ||
| U0164 | - | - | - | ||
| U1107 | - | - | - | ||
| Power Management Control ECU (Power Management CPU) | U0140 | - | - | - | |
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | |
| Steering Sensor | - | - | - | - | |
| Sub Bus 15 | ECM | U0293 | ○ | ○ | ○ |
| Brake Booster with Master Cylinder Assembly (Skid Control ECU) | U0073 | - | - | - | |
| U0123 | - | - | - | ||
| U0124 | - | - | - | ||
| U0126 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Management Control ECU (HV CPU) | U0100 | ○ | ○ | ○ | |
| U0129 | ○ | ○ | ○ | ||
| U0140 | - | - | - | ||
| U0151 | - | - | - | ||
| U0164 | - | - | - | ||
| U1107 | ○ | ○ | ○ | ||
| Power Management Control ECU (HV CPU) (Cruise Control) | U0122 | - | - | - | |
| CAN BUS WAVEFORMS |

CAN bus waveforms (Group 1)
![]() |
Normal waveform
![]() |
Open in both of the lines (CANH and CANL) of a CAN branch
![]() |
Short between the CAN bus lines (CANH and CANL)
CAN bus waveforms (reference) (Group 2)
![]() |
Open in a CAN branch line (CANH)
![]() |
Open in a CAN branch line (CANL)
![]() |
Open in a CAN main bus line (CANH)
![]() |
Short between a CAN bus line (CANH) and ground
![]() |
Short between a CAN bus line (CANL) and ground
| DATA SENDING/RECEIVING TABLE |
Data sending/receiving table
| Data content | Data Detected and Sent by | Data Received from (Can be Checked in Data List) | Data Received (Cannot be Checked in Data List) | Relevant Data List Item [Selected System] |
| Accelerator position | Power management control ECU (HV CPU) | - |
|
|
| Engine speed | ECM |
|
|
|
| Engine coolant temperature | ECM |
| - |
|
| Vehicle speed | Brake booster with master cylinder assembly (Skid control ECU) |
| Airbag sensor assembly |
|
| Combination meter assembly*3 |
|
|
| |
| Wheel speed | Brake booster with master cylinder assembly (Skid control ECU) | - | Power steering ECU assembly |
|
| Shift position | Power management control ECU (HV CPU) |
|
|
|
| Ambient temperature | Air conditioning amplifier assembly |
|
|
|
| Driver door courtesy | Multiplex network body ECU | - |
| FR Door Courtesy [Main Body] |
| Steering angle sensor | Steering sensor |
|
|
|
| Yaw rate sensor | Airbag sensor assembly (Yaw rate sensor) | Brake booster with master cylinder assembly (Skid control ECU) | Power steering ECU assembly |
|
| Deceleration sensor | Airbag sensor assembly (Acceleration sensor) | Brake booster with master cylinder assembly (Skid control ECU) |
|
|
| Power management control ECU (HV CPU) power source voltage | Power management control ECU (HV CPU)*1 | - | - | +B [Hybrid Control] |
| Power management control ECU (Power Management CPU) power source state | Power management control ECU (Power management CPU)*1 | - | - | Power Supply Condition [Power Source Control] |
| ECM power source voltage | ECM*1 | - | - | Battery Voltage [Engine and ECT] |
| Brake pedal stroke sensor | Brake booster with master cylinder assembly (Skid control ECU)*1 | - | - |
|
| Power steering ECU assembly power source voltage | Power steering ECU assembly*1 | - | - | Battery Voltage [EMPS] |
| Intensity of light received by the solar sensor | Air conditioning amplifier assembly*1 | - | - |
|
| Combination meter assembly power source voltage | Combination meter assembly*1 | - | - | +B Voltage Value [Combination Meter] |
| Clearance sonar main switch | Clearance warning ECU assembly*1 | - | - | Main Switch [Clearance Sonar] |
| Radio and display receiver assembly power source voltage | Radio and display receiver assembly*1 | - | - | Battery Voltage [Navigation System] |
| Driver door touch sensor | Smart key ECU assembly (Certification ECU)*1 | - | - | D-Door Touch Sensor [Entry&Start] |
Details of relevant Data List items (Selected system: Hybrid Control)
Connect the Intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List.
Check the results by referring to the following table.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Engine Revolution | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm | While idling after the engine is warmed up and inspection mode: Approximately 900 rpm While driving at a constant speed: No significant fluctuation | - |
| Vehicle Spd | Vehicle speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) While driving at a constant speed: No significant fluctuation | - |
| +B | Auxiliary battery voltage/ Min.: 0.00 V, Max.: 65.53 V | Constant: 10.00 to 15.00 V | Auxiliary battery voltage |
| Accel Pedal Pos #1 | Accelerator pedal position sensor No.1/ Min.: 0.0%, Max.: 100.0% | Accelerator pedal depressed: Changes with accelerator pedal pressure | Accelerator pedal sensor assembly |
| Accel Pedal Pos #2 | Accelerator pedal position sensor No.2/ Min.: 0.0%, Max.: 100.0% | Accelerator pedal depressed: Changes with accelerator pedal pressure | Accelerator pedal sensor assembly |
| Ambient Temperature | Ambient air temperature/ Min.: -40°C (-40°F), Max.: 215°C (419°F) | Power switch on (IG): Same as ambient air temperature | Ambient temperature sensor |
| Shift Sensor SW - P | Shift lever position sensor/ ON or OFF | Shift lever in P: ON Shift lever in any position other than P: OFF | Shift lever position sensor |
| Shift Sensor SW - R | Shift lever position sensor/ ON or OFF | Shift lever in R: ON Shift lever in any position other than R: OFF | Shift lever position sensor |
| Shift Sensor SW - N | Shift lever position sensor/ ON or OFF | Shift lever in N: ON Shift lever in any position other than N: OFF | Shift lever position sensor |
| Shift Sensor SW - D | Shift lever position sensor/ ON or OFF | Shift lever in D: ON Shift lever in any position other than D: OFF | Shift lever position sensor |
| Shift Sensor SW - B | Shift lever position sensor/ ON or OFF | Shift lever in B: ON Shift lever in any position other than B: OFF | Shift lever position sensor |
Details of relevant Data List items (Selected system: Power Source Control)
Connect the Intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the Intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
Check the results by referring to the following table.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Power Supply Condition | Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON | All OFF: Power switch off (ACC and IG) ACC ON: Power switch on (ACC) IG1 ON: Power switch on (IG) (IG1 relay on) IG2 ON: Power switch on (IG) (IG2 relay on) ST ON: Sending hybrid control system start request signal | Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time). |
Details of relevant Data List items (Selected system: Engine and ECT)
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Warm up the engine.
Turn the A/C switch off.
Turn the power switch off.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm | 900 to 1050 rpm: Idling | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Coolant Temp | Coolant temperature/ Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Battery Voltage | Auxiliary battery voltage/ Min.: 0 V, Max.: 65.535 V | 11 to 16 V: Power switch on (IG) | If 11 V or less, characteristics of some electrical components may change. |
| Ambient Temp for A/C | Ambient temperature for A/C/ Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
Details of relevant Data List items (Selected system: ABS/VSC/TRC)
Warm up the engine.
Turn the power switch off.
Connect the Intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the Intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the Intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stroke Sensor | Brake pedal stroke sensor assembly / Min.: 0.00 V, Max.: 5.00 V | When brake pedal released: 0.65 to 1.35 V | Reading increases when brake pedal is depressed |
| Stroke Sensor2 | Brake pedal stroke sensor assembly 2 / Min.: 0.00 V, Max.: 5.00 V | When brake pedal released: 3.65 to 4.35 V | Reading decreases when brake pedal is depressed |
| Deceleration Sensor | Acceleration sensor 1 / Min.: -18.525 m/s2, Max.: 18.387 m/s2
| - | During deceleration/acceleration: Changes continuously |
| Deceleration Sensor2 | Acceleration sensor 2 / Min.: -18.525 m/s2, Max.: 18.387 m/s2
| - | During deceleration/acceleration: Changes continuously |
| Yaw Rate Sensor | Yaw rate sensor 1 / Min.: -128°/s, Max.: 127°/s | Vehicle stationary: 0°/s Turning right: -128 to 0°/s Turning left: 0 to 127°/s | - |
| Yaw Rate Sensor2 | Yaw rate sensor 2 / Min.: -128°/s, Max.: 127°/s | Vehicle stationary: 0°/s Turning right: -128 to 0°/s Turning left: 0 to 127°/s | - |
| Steering Angle Sensor | Steering angle sensor / Min.: -3276.8°, Max.: 3276.7° | Turning left: Increases Turning right: Decreases | - |
| FR Wheel Speed | Front speed sensor RH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front speed sensor LH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear speed sensor RH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear speed sensor LH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed | Maximum wheel speed sensor / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Details of relevant Data List items (Selected system: EMPS)
Turn the power switch off.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Chassis / EMPS / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Meter Vehicle Velocity | Vehicle speed from meter/ Min.: 0 km/h (0 mph) Max.: 300.0 km/h (186.4 mph) | 0 km/h (0 mph) | Power switch on (READY) and vehicle stopped |
| No significant fluctuation | Power switch on (READY) and vehicle driven at a constant speed | ||
| Steering Angle Velocity | Steering angle speed/ Min.: -32768 deg/s Max.: 32767 deg/s | Value changes in proportion to steering speed -The value increases when turning left and decreases when turning right | Power switch on (READY) and steering wheel being turned |
| Battery Voltage | Auxiliary battery voltage/ Min.: 0 V Max.: 25.5 V | 9 to 16 V | Power switch on (IG) |
Details of relevant Data List items (Selected system: Navigation System)
Connect the intelligent tester to the DLC3.
Turn the power switch on (READY).
Turn the intelligent tester on.
Enter the following menus: Body / Navigation System / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Battery Voltage | Auxiliary battery voltage/Min.: 0 V, Max.:24 V | 11 to 14 V | - |
| Reverse Signal | Reverse signal/ON or OFF | ON: Shift lever in R OFF: Shift lever in any position other than R | - |
| Vehicle Speed | Maximum wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Details of relevant Data List items (Selected system: Clearance Sonar)
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the clearance sonar main switch on.
Turn the intelligent tester on.
Enter the following menus: Body / Clearance Sonar / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Main Switch | Clearance sonar main switch/OFF or ON | OFF: Clearance sonar main switch off ON: Clearance sonar main switch on | - |
| Parking Signal | Parking signal/OFF or ON | OFF: Shift lever in any position other than P ON: Shift lever in P | - |
| Reverse Signal | Reverse signal/OFF or ON | OFF: Shift lever in any position other than R ON: Shift lever in R | - |
| Vehicle Speed Info | Vehicle speed signal/Snr Stop or Snr Work | Snr Stop: Vehicle speed approximately 13 km/h (8.1 mph) or more (when accelerating) or approximately 9 km/h (5.6 mph) or more (when decelerating) Snr Work: Vehicle speed less than approximately 13 km/h (8.1 mph) (when accelerating) or less than approximately 9km/h (5.6 mph) (when decelerating) | - |
Details of relevant Data List items (Selected system: Entry&Start)
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D-Door Touch Sensor | Driver door touch sensor (unlock sensor) / ON or OFF | ON: Driver door touch sensor (unlock sensor) touched OFF: Driver door touch sensor (unlock sensor) not touched |
|
Details of relevant Data List items (Selected system: Combination Meter)
Warm up the engine.
Turn the power switch off.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed Meter | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost the same as actual vehicle speed | - |
| Engine Rpm | Engine speed/Min.: 0 rpm, Max.: 12750 rpm | 950 to 1050 rpm: Idling | - |
| Coolant Temperature | Engine coolant temperature/-40 to 127.5°C (-40 to 261.5°F) | After warming up: 75 to 100°C (167 to 212°F) |
|
| +B Voltage Value | Auxiliary battery voltage/Min.: 0 V, Max.: 25.5 V | 11 to 16 V | - |
| Ambient Temperature | Outside temperature/Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F) | Almost the same as actual outside temperature | The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F) |
Details of relevant Data List items (Selected system: Air Conditioner)
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ambient Temp Sensor | Ambient temperature sensor (thermistor assembly) / Min.: -23.30°C (-9.94°F) Max.: 65.95°C (150.71°F) | Actual ambient temperature displayed | - |
| Solar Sensor (D Side) | Driver side automatic light control sensor (solar sensor) / Min.: 0 Max.: 255 | Driver side automatic light control sensor (solar sensor) value increases as brightness increases | - |
| Solar Sensor (P Side) | Front passenger side automatic light control sensor (solar sensor) / Min.: 0 Max.: 255 | Front passenger side automatic light control sensor (solar sensor) value increases as brightness increases | - |
| Engine Coolant Temp | Engine coolant temperature sensor / Min.: 1.30°C (34.34°F) Max.: 90.55°C (194.99°F) | Actual engine coolant temperature displayed | - |
Details of relevant Data List items (Selected system: Main Body ECU) (Multiplex Network Body ECU)
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Door Courtesy | Front door courtesy light switch RH / ON or OFF | ON: Front door RH closed OFF: Front door RH open | - |