Home › Drivetrain › P314 HYBRID TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE

TRANSMISSION CONTROL CABLE > REMOVAL

for Preparation Click here



1. REMOVE COOL AIR INTAKE DUCT SEAL


    B379695
  1. Remove the 9 clips and cool air intake duct seal.



2. REMOVE INLET AIR CLEANER ASSEMBLY


    A259747
  1. Remove the 2 bolts and inlet air cleaner assembly.



3. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A259032
  1. Disconnect the mass air flow meter connector and wire harness clamp from the air cleaner cap sub-assembly.

  1. Disconnect the ventilation hose from the cylinder head cover.

  1. Disconnect the connector.



    A259031
  1. Release the 2 clamps and remove the air cleaner cap sub-assembly.



    A259684E01
  1. Disconnect the 2 fuel vapor feed hoses.
    Text in Illustration 
    *1
    Retainer
    *2
    Fuel Tube Connector
    *3
    Pipe
    *4
    O-ring
    *a
    Pull

    NOTICE:
    1. Remove any dirt or foreign matter on the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel vapor feed hose.



    A259033
  1. Loosen the hose clamp and disconnect the air cleaner hose from the throttle with motor body assembly.



4. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


5. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A259768E03
  1. Remove the 2 bolts and air cleaner case sub-assembly.
    Text in Illustration 
    *a
    Projection



6. REMOVE AIRBAG SENSOR ASSEMBLY
(Click here)


7. REMOVE ACCELERATOR PEDAL SENSOR ASSEMBLY

NOTICE:
  1. Avoid physical shock to the accelerator pedal sensor assembly.
  2. Do not disassemble the accelerator pedal sensor assembly.
  3. The accelerator pedal sensor assembly does not require lubrication.
  4. Do not apply oil or other lubricants to the accelerator pedal sensor assembly. If applied, the accelerator pedal sensor assembly must be replaced.



    A254797E03
  1. Disconnect the connector.
    Text in Illustration 
    *a
    for LHD:
    *b
    for RHD:

  1. Remove the 2 bolts and accelerator pedal sensor assembly.



8. DISCONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY (for LHD)
  1. Turn back the floor carpet.



    C240462
  1. Remove the bolt and nut, and disconnect the No. 1 parking brake cable assembly.



9. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY (for LHD)
  1. Move the shift lever to N.



    C239451
  1. Disconnect the end of the transmission control cable from the lower shift lever assembly.

  1. Disengage the 2 claws and disconnect the transmission control cable assembly from the lower shift lever assembly.



    A268022
  1. Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.

  1. Using a screwdriver, disengage the 4 claws and disconnect the transmission control cable assembly with clip from the No. 1 transmission control cable bracket.

  1. Remove the clip from the transmission control cable assembly.



    C243612
  1. Disconnect the transmission control cable assembly from the 2 transmission control cable brackets.



    C241623E01
  1. Remove the bolt and disconnect the No. 1 parking brake cable assembly from the body.
    Text in Illustration 
    *1
    No. 1 parking brake cable assembly
    *2
    Transmission control cable assembly

  1. Turn back the dash panel insulator.

  1. Remove the 2 bolts and pull out the transmission control cable assembly from the body.



10. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY (for RHD)
  1. Move the shift lever to N.



    C244182
  1. Disconnect the end of transmission control cable assembly from the lower shift lever assembly.

  1. Disengage the 2 claws and disconnect the transmission control cable assembly from the lower shift lever assembly.



    A268022
  1. Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.

  1. Using a screwdriver, disengage the 4 claws and disconnect the transmission control cable assembly with clip from the No. 1 transmission control cable bracket.

  1. Remove the clip from the transmission control cable assembly.



    C243612
  1. Disconnect the transmission control cable assembly from the 2 transmission control cable brackets.



    C241623E01
  1. Remove the bolt and disconnect the No. 1 parking brake cable assembly from the body.
    Text in Illustration 
    *1
    No. 1 parking brake cable assembly
    *2
    Transmission control cable assembly

  1. Turn back the dash panel insulator.

  1. Remove the 2 bolts and pull out the transmission control cable assembly from the body.