Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS (for TMC, TMMR Made)

WINDSHIELD GLASS (for TMC, TMMR Made) > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
  1. Using a brush or sponge, coat the application area of 2 new No. 2 windshield glass stoppers with Primer G.

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



  1. Install the 2 new No. 2 windshield glass stoppers onto the windshield glass, as shown in the illustration.


    B280220E01


    Text in Illustration 
    *A
    Back Side
    -
    -
    *1
    Ceramic Notch
    -
    -
    *a
    Windshield Glass Edge Side
    -
    -

    Standard Dimension:

    Area
    Dimension
    a
    13.7 to 14.7 mm (0.539 to 0.578 in.)

    NOTICE:
    Only 2-piece type windshield glass stoppers are provided as supply parts. Use the 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



2. INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)


    B280219
  1. Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.

    NOTICE:
    Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



3. INSTALL WINDSHIELD GLASS RETAINER
  1. Using a brush or sponge, coat the application area of 2 new windshield glass retainers with Primer G.

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    1. If an area other than specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.
    2. Depending on the vehicle, either 1 or 2 windshield retainers may be present.



    B280221E01
  1. Install the 2 windshield glass retainers onto the windshield glass as shown in the illustration.
    Text in Illustration 
    *A
    Back Side
    *1
    Ceramic Notch

    HINT:
    For vehicles with only 1 windshield glass retainer, install the new windshield glass retainer on the same side as the removed one.



4. INSTALL WINDSHIELD OUTSIDE MOULDING
  1. Using a brush or sponge, coat the application area of a new windshield outside moulding with Primer G.

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



    B280253E01
  1. Install the windshield outside moulding onto the windshield glass as shown in the illustration.
    Text in Illustration 
    *A
    Back Side

    Standard Dimension:
    Area
    Dimension
    a
    6.7 mm (0.264 in.)



5. INSTALL WINDSHIELD GLASS ADHESIVE DAM


  1. Using a brush or sponge, coat the application area of a new windshield glass adhesive dam with Primer G.


    B289717E01


    Text in Illustration 
    *A
    Back Side
    -
    -
    *1
    Primer G
    *2
    Ceramic Notch
    *3
    Label Area
    -
    -

    Standard Dimension:

    Area
    Dimension
    a
    33.0 mm (1.30 in.)
    b
    10.0 mm (0.394 in.)
    c
    55.0 mm (2.17 in.)

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G to dry for 3 minutes or more.
    3. Throw away any leftover primer G.
    4. Keep label area clear of primer G.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



  1. Install the windshield glass adhesive dam onto the windshield glass as shown in the illustration.


    B289722E01


    Text in Illustration 
    *A
    Back Side
    -
    -
    *1
    Ceramic Notch
    *2
    Windshield Glass Adhesive Dam

    Standard Dimension:

    Area
    Dimension
    a
    36.0 mm (1.42 in.)



6. INSTALL WINDSHIELD GLASS SUB-ASSEMBLY


    B380739E01
  1. Position the windshield glass sub-assembly.
    Text in Illustration 
    *1
    Matchmark

    1. Using suction cups, place the windshield glass sub-assembly in the correct position.

    2. Check that the whole contact surface of the windshield glass sub-assembly rim is perfectly even.

    3. Align the matchmarks on the windshield glass sub-assembly and vehicle body.

      NOTICE:
      Check that the windshield glass stoppers and windshield glass retainers are attached to the vehicle body correctly.

    4. Remove the windshield glass sub-assembly.



  1. Using a brush, coat the installation surface on the vehicle body with Primer M.


    B280223E01


    Text in Illustration 
    *1
    Brush
    *2
    Primer M
    *3
    Adhesive
    -
    -
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Do not coat the adhesive with Primer M.
    2. Do not apply too much primer M.
    3. Allow the primer M to dry for 3 minutes or more.
    4. Throw away any leftover primer M.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



  1. Using a brush or sponge, coat the application area of adhesive with Primer G.


    B280225E01


    Text in Illustration 
    *A
    Back Side
    -
    -
    *1
    Primer G
    *2
    Ceramic Notch
    *3
    Adhesive Center
    -
    -

    Standard Dimension:

    Area
    Dimension
    a
    9.6 mm (0.378 in.) or more
    b
    16.5 mm (0.650 in.) or more
    c
    18.5 mm (0.728 in.) or more
    d
    11.0 mm (0.433 in.) or more

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    1. Apply Primer G onto the ceramic notches.
    2. If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



  1. Apply adhesive to the glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent




      B214800E10
    1. Cut off the tip of the cartridge nozzle as shown in the illustration.
      Text in Illustration 
      *1
      Nozzle

      Standard Dimension:
      Area
      Dimension
      a
      8.0 mm (0.315 in.) or more
      b
      12.0 mm (0.472 in.) or more

      HINT:
      After cutting off the tip, use all adhesive within the time described in the table below.

      Usage Time Frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour and 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the windshield glass sub-assembly as shown in the illustration.


      B280226E01


      Text in Illustration 
      *A
      Back Side
      -
      -
      *1
      Adhesive
      *2
      Ceramic Notch
      *3
      Adhesive Center
      -
      -

      Standard Dimension:

      Area
      Dimension
      a
      9.5 mm (0.374 in.)
      b
      9.5 mm (0.374 in.)
      c
      4.0 mm (0.157 in.)
      d
      8.0 mm (0.315 in.)
      e
      4.0 mm (0.157 in.)

      HINT:
      Apply adhesive onto the ceramic notches.



    B380739E01
  1. Install the windshield glass sub-assembly.
    Text in Illustration 
    *1
    Matchmark

    1. Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.

      NOTICE:
      1. Check that the windshield glass stoppers and windshield glass retainers are attached to the vehicle body correctly.
      2. Check the clearance between the vehicle body and windshield glass sub-assembly.

      HINT:
      Depending on the vehicle, either 1 or 2 windshield retainers may be present.

    2. Lightly press the front surface of the windshield glass sub-assembly to ensure that the windshield glass is securely fit to the vehicle body.

      HINT:
      Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.

    3. Using a scraper, remove any excess or protruding adhesive.

    4. Hold the windshield glass using protective tape until the applied adhesive becomes hard.

      NOTICE:
      Do not drive the vehicle for the time described in the table below.

      Minimum Time:
      Temperature
      Minimum Time prior to Driving Vehicle
      35°C (95°F)
      1 hour and 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours

  1. w/ Window Deicer System:

    1. Engage the clamp and connect the connector.

  1. w/ Heated Windshield Defroster System:

    1. Engage the 2 clamps and connect the 2 connectors.



7. INSPECT FOR LEAK AND REPAIR
  1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

  1. If water leaks into the cabin, allow the water to dry and add adhesive.

  1. Remove the protective tape.



8. INSTALL ROOF HEADLINING ASSEMBLY
  1. Return the front section of the roof headlining assembly to the original position.



9. INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)


    B405329E02
  1. Align the alignment mark on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.
    Text in Illustration 
    *1
    Notch
    *2
    Alignment Mark
    *3
    Tape

    NOTICE:
    After installation, check that the corners fit correctly.

    HINT:
    Make sure that the tape is positioned as shown in the illustration.



10. INSTALL VISOR HOLDER


    B211698
  1. Engage the 2 claws.

  1. Push in the visor holder as shown in the illustration.

    HINT:
    Use the same procedure for the other visor holder.



11. INSTALL VISOR ASSEMBLY LH
  1. Install the visor assembly LH with the 2 screws.



12. INSTALL VISOR BRACKET COVER (for LH Side)


    B278993
  1. Engage the 4 claws to install the visor bracket cover.



13. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



14. INSTALL VISOR BRACKET COVER (for RH Side)

HINT:
Use the same procedure as for the LH side.



15. INSTALL REAR ASSIST GRIP ASSEMBLY LH


    B279002
  1. Put an rear assist grip assembly LH together as shown in the illustration.



    B279004
  1. Engage the 2 clips to install the rear assist grip assembly LH.



    B278998
  1. Engage the 4 claws to install the 2 assist grip covers



16. INSTALL REAR ASSIST GRIP ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



17. INSTALL ASSIST GRIP SUB-ASSEMBLY


    B279001
  1. Put an assist grip sub-assembly together as shown in the illustration.



    B279003
  1. Engage the 2 clips to install the assist grip sub-assembly.



    B278996
  1. Engage the 4 claws to install the 2 assist grip covers

    HINT:
    Use the same procedure for the RH side.



18. INSTALL SPOT LIGHT ASSEMBLY
  1. Connect the connector.



    E227610E01
  1. Engage the 4 claws to install the spot light assembly.
    Text in Illustration 
    *a
    Front



19. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)
  1. Connect the connector.



    E227555
  1. Engage the 4 clips to install the roof console box assembly.



20. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)
  1. Connect the connector.



    E227557
  1. Engage the 4 clips to install the roof console box assembly.



21. INSTALL FRONT PILLAR GARNISH LH
  1. Remove the protective cover.

  1. Make sure that the front pillar garnish clip is not damaged.

    NOTICE:
    If there is any damage, replace the garnish clip with a new one.



    B278987

    B453135E01

  1. Install the front pillar garnish clip to front pillar garnish LH.

    HINT:
    Install the front pillar garnish clip so that it faces as shown in the illustration.


    Text in Illustration 
    *a
    Correct
    *b
    Incorrect

  1. Engage the 2 guides as shown in the illustration.



    B278984
  1. Engage the 2 clips to install the front pillar garnish LH.



22. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B278980E01
  1. Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *1
    Alignment Mark (Yellow)

    NOTICE:
    After installation, check that the corners fit correctly.



23. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedure as for the LH side.



24. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B278981E01
  1. Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
    Text in Illustration 
    *1
    Alignment Mark (White)

    NOTICE:
    After installation, check that the corners fit correctly.



25. INSTALL RAIN SENSOR (w/ Rain Sensor)
(Click here)


26. INSTALL INNER REAR VIEW MIRROR ASSEMBLY
(Click here)


27. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


  1. Engage the 8 guides as shown in the illustration.


    E226235



  1. Engage the 6 claws and guide to install the cowl top ventilator louver sub-assembly.


    E226233



28. INSTALL FRONT FENDER TO COWL SIDE SEAL LH


  1. for TMC,TMMR Made:



      E226231
    1. Engage the 3 guides and 2 clips to install the front fender to cowl side seal LH as shown in the illustration.



  1. for TMMK Made:



      E314350
    1. Engage the guide and 2 clips to install the front fender to cowl side seal LH as shown in the illustration.



29. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:
Use the same procedure as for the LH side.



30. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E226523E04
  1. When reusing the front wiper arm and blade assembly LH:

    1. Clean the wiper arm serrations.
      Text in Illustration 
      *a
      Wiper Arm Serration



    E231343E02
  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.
      Text in Illustration 
      *a
      Wiper Pivot Serration



    E226090E03
  1. Set the front wiper arm and blade assembly LH in the range shown in the illustration and then install the front wiper arm and blade assembly LH with the nut.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    Area
    Measurement
    A
    7.5mm (0.295 in.)
    Text in Illustration 
    *1
    Ceramic Dot

    HINT:
    Hold the wiper arm by hand while tightening the nut.



31. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E226523E04
  1. When reusing the front wiper arm and blade assembly RH:

    1. Clean the wiper arm serrations.
      Text in Illustration 
      *a
      Wiper Arm Serration



    E231343E02
  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.
      Text in Illustration 
      *a
      Wiper Pivot Serration



    E226089E03
  1. Set the front wiper arm and blade assembly RH in the range shown in the illustration and then install the front wiper arm and blade assembly RH with the nut.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    Area
    Measurement
    A
    7.5mm (0.295 in.)
    Text in Illustration 
    *1
    Ceramic Dot

    HINT:
    Hold the wiper arm by hand while tightening the nut.

  1. Turn the ignition switch to ON.

  1. Operate the front wiper while spraying washer fluid onto the windshield glass. Make sure that the front wiper functions properly and the wiper does not come into contact with the vehicle body.

  1. Lift each wiper arm twice after the wipers stop and check the wiper set position.

  1. Turn the ignition switch off.