BACK WINDOW GLASS (for TMMK Made) > INSTALLATION |
| 1. INSTALL NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type) |
Using a brush or sponge, coat the installation area of 2 new No. 2 back window glass stoppers with primer G.
![]() |
Install the 2 new No. 2 back window glass stoppers to the back window glass as shown in the illustration.
| *A | Back Side |
| *1 | Ceramic Notch |
| *a | Back Window Glass Edge |
| Area | Dimension |
| a | 14.2 to 15.2 mm (0.559 to 0.598 in.) |
| 2. INSTALL NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type) |
![]() |
Install 2 new No. 1 back window glass stoppers to the vehicle body as shown in the illustration.
| 3. INSTALL BACK WINDOW OUTSIDE MOULDING |
Using a brush or sponge, coat the installation area of a new back window outside moulding with primer G.
![]() |
Install the new back window outside moulding to the back window glass as shown in the illustration.
| *A | Back Side |
| Area | Dimension |
| a | 7.4 mm (0.291 in.) |
| 4. INSTALL BACK WINDOW GLASS ADHESIVE DAM |
Using a brush or sponge, coat the installation area of a new back window glass adhesive dam with primer G.
Install the new back window glass adhesive dam to the back window glass as shown in the illustration.

| *A | Back Side | - | - |
| *1 | Ceramic Notch | - | - |
| *a | Adhesive Center Line | - | - |
| Area | Dimension |
| a | 10.0 mm (0.394 in.) |
| 5. INSTALL BACK WINDOW GLASS SUB-ASSEMBLY |
![]() |
Position the back window glass sub-assembly.
| *1 | Matchmark |
Using suction cups, place the back window glass sub-assembly in the correct position.
Check that the whole contact surface of the back window glass sub-assembly is perfectly even.
Align the matchmarks on the back window glass sub-assembly and vehicle body.
Remove the back window glass sub-assembly.
Using a brush, coat the installation surface on the vehicle body with primer M.

| *1 | Brush | *2 | Primer M |
| *3 | Adhesive | - | - |
| *a | Correct | *b | Incorrect |
Using a brush or sponge, coat the adhesive application area with primer G.

| *A | Back Side | - | - |
| *1 | Ceramic Notch | *2 | Primer G |
| *a | Adhesive Center Line | - | - |
| Area | Dimension |
| a | 18.5 mm (0.728 in.) or more |
| b | 14.0 mm (0.551 in.) or more |
| c | 14.0 mm (0.551 in.) or more |
| d | 11.0 mm (0.433 in.) or more |
Apply adhesive to the back window glass sub-assembly.
![]() |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| *1 | Nozzle |
| Area | Dimension |
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
Load the sealer gun with the cartridge.
Apply adhesive to the back window glass sub-assembly as shown in the illustration.

| *A | Back Side | - | - |
| *1 | Ceramic Notch | *2 | Adhesive |
| *a | Adhesive Center Line | - | - |
| Area | Dimension |
| a | 6.5 mm (0.256 in.) |
| b | 8.0 mm (0.315 in.) |
| c | 10.0 mm (0.394 in.) |
| d | 10.0 mm (0.394 in.) |
| e | 16.5 mm (0.650 in.) |
Install the back window glass sub-assembly.
![]() |
Using suction cups, position the back window glass sub-assembly so that the matchmarks are aligned, and press it in gently along the rim.
| *1 | Matchmark |
Lightly press the front surface of the back window glass sub-assembly to ensure that the back window glass sub-assembly is securely fit to the vehicle body.
Using a scraper, remove any excess or protruding adhesive.
Hold the back window glass sub-assembly using protective tape until the applied adhesive becomes hard.
| Temperature | Minimum Time Prior to Driving Vehicle |
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
Connect each connector.
| 6. INSPECT FOR LEAK |
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
| 7. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY |
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
![]() |
Engage the 5 guides and 3 clips to install the package tray trim panel assembly.
| 8. INSTALL REAR SEAT SHOULDER BELT COVER |
![]() |
Engage the 4 guides and 2 claws to install the rear seat shoulder belt cover.
| 9. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR COVER |
![]() |
Engage the 2 guides and 2 claws to install the child restraint seat tether anchor cover.
| 10. INSTALL CENTER STOP LIGHT SET |
Connect the connector.
Temporarily install the center stop light set.
![]() |
Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to engage the 4 claws.
| 11. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH |
for Type A:
![]() |
Connect the floor anchor of the rear seat inner with center belt assembly LH with the bolt.
| *a | Protruding Part |
for Type B:
![]() |
Connect the floor anchor of the rear seat inner with center belt assembly LH with the bolt.
| *a | Protruding Part |
| 12. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH |
Install the child restraint seat anchor bracket sub-assembly LH with the 2 nuts.
| 13. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side) |
![]() |
Connect the floor anchor of the rear seat outer belt assembly with the bolt.
| *a | Protruding Part |
| 14. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side) |
![]() |
Connect the floor anchor of the rear seat outer belt assembly with the bolt.
| *a | Protruding Part |
| 15. INSTALL ROOF HEADLINING ASSEMBLY |