Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (for TMMK Made)

ROOF HEADLINING (for TMMK Made) > INSTALLATION

for Preparation Click here



1. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)


    B279105E02
  1. Install the 2 clips to the roof headlining assembly.
    Text in Illustration 
    *a
    Clip (Black)
    *b
    Clip (White)



    B279011
  1. Put the roof headlining assembly into the vehicle through the front door RH.

    NOTICE:
    Do not damage the roof headlining assembly or vehicle interior.



  1. Engage the 2 clips.


    B396427

  1. Install the roof headlining assembly with the 2 clips.

  1. Engage the 4 clamps to the front pillar LH.

  1. Engage the 3 clamps to the front pillar RH.

  1. Connect the bracket with the bolt to the front pillar RH.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Engage the 2 clamps and connect the connector to the rear pillar RH.

  1. w/ EC Mirror:

    1. Connect the connector to the inner rear view mirror.



2. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    B279105E02
  1. Install the 2 clips to the roof headlining assembly.
    Text in Illustration 
    *a
    Clip (Black)
    *b
    Clip (White)



    B279012
  1. Put the roof headlining assembly into the vehicle through the front door RH.

    NOTICE:
    Do not damage the roof headlining assembly or vehicle interior.



  1. Engage the 2 clips.


    B396428

  1. Install the roof headlining assembly with the 2 clips.

  1. Engage the 4 clamps to the front pillar LH.

  1. Engage the 3 clamps to the front pillar RH.

  1. Connect the bracket with the bolt to the front pillar RH.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Engage the 2 clamps and connect the connector to the rear pillar RH.

  1. Connect the connector to the sliding roof drive gear assembly.

  1. w/ EC Mirror:

    1. Connect the connector to the inner rear view mirror.



3. INSTALL VISOR HOLDER


    B211698
  1. Engage the 2 claws.

  1. Push in the visor holder as shown in the illustration.

    HINT:
    Use the same procedure for the other visor holder.



4. INSTALL VISOR ASSEMBLY LH
  1. Install the visor assembly LH with the 2 screws.



5. INSTALL VISOR BRACKET COVER (for LH Side)


    B278993
  1. Engage the 4 claws to install the visor bracket cover.



6. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



7. INSTALL VISOR BRACKET COVER (for RH Side)

HINT:
Use the same procedure as for the LH side.



8. INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)


    B279103E02
  1. Align the alignment mark on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.
    Text in Illustration 
    *a
    Notch
    *b
    Alignment Mark

    NOTICE:
    After installation, check that the corners fit correctly.



9. INSTALL ASSIST GRIP SUB-ASSEMBLY


    B279001
  1. Put the assist grip sub-assembly together as shown in the illustration.



    B279003
  1. Engage the 2 clips to install the assist grip sub-assembly.



    B278996
  1. Engage the 4 claws to install the 2 assist grip covers.

    HINT:
    Use the same procedure for the RH side.



10. INSTALL REAR ASSIST GRIP ASSEMBLY LH


    B279002
  1. Put the rear assist grip assembly LH together as shown in the illustration.



    B279004
  1. Engage the 2 clips to install the rear assist grip assembly LH.



    B278998
  1. Engage the 4 claws to install the 2 assist grip covers.



11. INSTALL REAR ASSIST GRIP ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



12. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)


    E220649E01
  1. Align the switch parts shown in the illustration and engage the 4 claws to install the room light switch base to the No. 1 room light housing.
    Text in Illustration 
    *a
    Switch Part of Room Light Switch Base
    *b
    Switch Part of No. 1 Room Light Housing



    E228311E01
  1. Engage the 4 claws to install the No. 1 room light housing.
    Text in Illustration 
    *a
    Front



    E228312E01
  1. Engage the 4 claws to install the No. 1 room light lens.
    Text in Illustration 
    *a
    Front



13. INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof)


    E227565E01
  1. Engage the 8 claws to install the map light sub-assembly to the spot light housing as shown in the illustration.
    Text in Illustration 
    *a
    Front



    E227563E01
  1. Engage the 6 claws to install the spot light housing.
    Text in Illustration 
    *a
    Front



    E227561E01
  1. Engage the 8 claws to install the 2 spot light lenses.
    Text in Illustration 
    *a
    Front



14. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)
  1. Connect the connector.



    E226708
  1. Engage the 4 clips to install the roof console box assembly.



15. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)
  1. Connect the connector.



    E226710
  1. Engage the 4 clips to install the roof console box assembly.



16. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


  1. except TMMR Made:

    1. Engage the 6 claws and temporarily install the inner rear view mirror stay holder cover.



    2. B281436
    3. Slide the inner rear view mirror stay holder cover in the direction indicated by arrow shown in the illustration and engage the 2 claws to install the cover.



  1. for TMMR Made:

    1. Engage the 2 claws to temporarily install the inner rear view mirror stay holder cover.



    2. B380968
    3. Slide the inner rear view mirror stay holder cover in the direction indicated by arrow shown in the illustration to engage the 2 guides and install the cover.



17. INSTALL INSTRUMENT PANEL ASSEMBLY
(Click here)


18. INSTALL FRONT SEAT ASSEMBLY LH
(Click here)


19. INSTALL FRONT SEAT ASSEMBLY RH
for Manual Seat: (Click here)
for Power Seat:

HINT:
Use the same procedure as for the LH side.



20. INSTALL ROOF SIDE INNER GARNISH LH
  1. Install 5 new clips to the roof side inner garnish LH.

  1. Engage the guide.

  1. Engage the 5 clips to install the roof side inner garnish LH.



21. INSTALL CENTER PILLAR UPPER GARNISH LH
  1. Install a new clip to the center pillar upper garnish LH.

  1. Pass the floor anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH.

  1. Engage the clip.

  1. Install the center pillar upper garnish LH with the 2 screws.



22. INSTALL CENTER PILLAR LOWER GARNISH LH
  1. Engage the 2 claws and 3 clips to install the center pillar lower garnish LH.



23. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
  1. Install the floor anchor of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the front seat outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.



24. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)
  1. Engage the 3 claws to install the lap belt outer anchor cover.



25. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B278982E02
  1. Align the alignment mark (Pink) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark (Pink)

    NOTICE:
    After installation, check that the corners fit correctly.



26. INSTALL REAR DOOR SCUFF PLATE LH
  1. Engage the 6 claws to install the rear door scuff plate LH.

    HINT:
    Engage the claws from the rear side of the scuff plate.



27. INSTALL ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedure as for the LH side.



28. INSTALL CENTER PILLAR UPPER GARNISH RH

HINT:
Use the same procedure as for the LH side.



29. INSTALL CENTER PILLAR LOWER GARNISH RH

HINT:
Use the same procedure as for the LH side.



30. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



31. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedure as for the LH side.



32. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B278983E02
  1. Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
    Text in Illustration 
    *a
    Alignment Mark (Blue)

    NOTICE:
    After installation, check that the corners fit correctly.



33. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



34. INSTALL REAR SIDE SEATBACK ASSEMBLY RH
  1. Engage the hook.

  1. Install the rear side seatback assembly RH with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the connector.

  1. Connect the rear seat outer belt assembly to the rear seat shoulder belt guide.



35. INSTALL REAR SIDE SEATBACK ASSEMBLY LH
  1. Engage the hook.

  1. Install the rear side seatback assembly LH with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the connector.

  1. Connect the rear seat outer belt assembly to the rear seat shoulder belt guide.



36. INSTALL REAR SEATBACK ASSEMBLY RH
  1. Place the rear seatback assembly RH in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly RH with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



37. INSTALL REAR SEATBACK ASSEMBLY LH
  1. Place the rear seatback assembly LH in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly LH with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



38. INSTALL INNER LUGGAGE COMPARTMENT TRIM PAD
  1. Install the inner luggage compartment trim pad.



39. INSTALL REAR SEAT CUSHION LOCK HOOK


    B393388
  1. Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure for the RH side and the LH side.



40. INSTALL REAR SEAT CUSHION ASSEMBLY
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly.



    B280250
  1. Engage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly to the 2 rear seat cushion lock hooks as shown in the illustration.

  1. Confirm that the rear seat cushion assembly is securely installed.

    NOTICE:
    When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.



41. INSTALL FRONT PILLAR GARNISH LH
  1. Remove the protective cover.

  1. Install a new clips to the front pillar garnish LH.



    B379545
  1. Install a new front pillar garnish clip to front pillar garnish LH.

    HINT:
    Engage the front pillar garnish clip so that it is oriented as shown in the illustration.

  1. Engage the 2 guides as shown in the illustration.



    B379546
  1. Engage the front pillar garnish clip and clip to install the front pillar garnish LH.



42. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B278980E02
  1. Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark (Yellow)

    NOTICE:
    After installation, check that the corners fit correctly.



43. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
  1. Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the clip.



44. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Engage the 10 claws to install the front door scuff plate LH.



45. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedure as for the LH side.



46. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B278981E02
  1. Align the alignment mark (White) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
    Text in Illustration 
    *a
    Alignment Mark (White)

    NOTICE:
    After installation, check that the corners fit correctly.



47. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



48. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



49. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



50. INSPECT SRS WARNING LIGHT
(Click here)