DTC P0115 Engine Coolant Temperature Circuit Malfunction |
DTC P0117 Engine Coolant Temperature Circuit Low Input |
DTC P0118 Engine Coolant Temperature Circuit High Input |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0115 | An open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| P0117 | A short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| P0118 | An open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) | Short circuit |
| Frequency of Operation | Continuous |
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temp.
Read the value displayed on the tester.
| Result | Proceed to |
| -40°C (-40°F) | A |
| 140°C (284°F) | B |
| Between 75 and 100°C (167 and 212°F) | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
Disconnect the engine coolant temperature sensor connector.

| *1 | Engine Coolant Temperature Sensor | *2 | ECM |
| *a | Front view of wire harness connector (to Engine Coolant Temperature Sensor) | - | - |
Connect terminals 1 (E2) and 2 (THW) of the engine coolant temperature sensor connector on the wire harness side.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temp.
Read the value displayed on the tester.
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E47-2 (THW) - E26-114 (THW) | Always | Below 1 Ω |
| E47-1 (E2) - E26-117 (ETHW) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the engine coolant temperature sensor connector.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temp.
Read the value displayed on the tester.
| *1 | Engine Coolant Temperature Sensor |
| *2 | ECM |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E47-2 (THW) or E26-114 (THW) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||