DTC P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) |
DTC P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) |
DTC P0057 Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2) |
DTC P0058 Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2) |
DTC P102D O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON |
DTC P105D O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0037 P0057 | Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic). |
|
| P0038 P0058 | Heated oxygen sensor heater current reaches high limit (Hybrid IC high current limiter monitor input "Fail") (1 trip detection logic). |
|
| P102D P105D | Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic). | ECM |
| Frequency of Operation | Continuous |
| Time after heater on | 10 seconds or more |
| Time after heater on | 10 seconds or more |
| Time after heater on | 10 seconds or more |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Inspect the heated oxygen sensor (Click here).
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR) |
Disconnect the heated oxygen sensor connector.

Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E22-2 (+B) - Body ground | Engine switch on (IG) | 11 to 14 V |
| E20-2 (+B) - Body ground | Engine switch on (IG) | 11 to 14 V |
| *1 | Bank 1 | *2 | Bank 2 |
| *a | Front view of wire harness connector (to Heated Oxygen Sensor) | - | - |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E22-1 (HT1B) - E26-28 (HT1B) | Always | Below 1 Ω |
| E20-1 (HT2B) - E26-22 (HT2B) | Always | Below 1 Ω |
| E22-1 (HT1B) or E26-28 (HT1B) - Body ground | Always | 10 kΩ or higher |
| E20-1 (HT2B) or E26-22 (HT2B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038, P0057, P0058, P102D OR P105D) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the tester on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0037, P0038, P0057, P0058, P102D or P105D is output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY) |
Disconnect the heated oxygen sensor connector.
Remove the No. 1 integration relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E22-2 (+B) - 1A-8 | Always | Below 1 Ω |
| E20-2 (+B) - 1A-8 | Always | Below 1 Ω |
| E22-2 (+B) or 1A-8 - Body ground | Always | 10 kΩ or higher |
| E20-2 (+B) or 1A-8 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||