Home › Engine / Hybrid System ยท 6AR-FSE › INTAKE / EXHAUST › EXHAUST PIPE

EXHAUST PIPE > INSTALLATION

for Preparation Click here



1. INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)


    A077857E03
  1. Using a vernier caliper, measure the free length of the 2 compression springs.
    Minimum Free Length
    40.5 mm (1.59 in.)
    If the length is less than the minimum, replace the compression spring.

  1. Temporarily install a new exhaust pipe gasket to the exhaust manifold converter sub-assembly (TWC: Front Catalyst).



    A181728E40
  1. Using a plastic hammer and wooden block, tap in the exhaust pipe gasket until its surface is flush with the exhaust manifold converter sub-assembly (TWC: Front Catalyst).
    Text in Illustration 
    *1
    Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
    *2
    Exhaust Pipe Gasket
    *a
    Wooden Block

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. Do not push in the gasket by using the exhaust pipe when connecting it.

  1. Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust pipe support.



  1. Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


    HINT:
    A258941E01
    After installation, check that the space between the flanges of the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.
    Text in Illustration 
    *1
    Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
    *2
    Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
    *3
    Exhaust Pipe Gasket
    *a
    Space between Flanges: 8.5 mm (0.335 in.)



2. INSTALL CENTER EXHAUST PIPE ASSEMBLY
  1. Install a new exhaust pipe gasket to the front exhaust pipe assembly (TWC: Rear Catalyst).

  1. Connect the center exhaust pipe assembly to the exhaust pipe support.

  1. Install the center exhaust pipe assembly to the front exhaust pipe assembly (TWC: Rear Catalyst) with the 2 nuts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



3. INSTALL TAIL EXHAUST PIPE ASSEMBLY


    A077857E03
  1. Using a vernier caliper, measure the free length of the 2 compression springs.
    Minimum Free Length
    38.5 mm (1.52 in.)
    If the free length is less than the minimum, replace the compression spring.

  1. Temporarily install a new exhaust pipe gasket to the center exhaust pipe assembly.



    A181728E40
  1. Using a plastic hammer and wooden block, tap in the exhaust pipe gasket until its surface is flush with the center exhaust pipe assembly.
    Text in Illustration 
    *1
    Center Exhaust Pipe Assembly
    *2
    Exhaust Pipe Gasket
    *a
    Wooden Block

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. Do not push in the gasket by using the exhaust pipes when connecting them.

  1. Connect the tail exhaust pipe assembly to the 3 exhaust pipe supports.



  1. Install the tail exhaust pipe assembly to the center exhaust pipe assembly with the 2 compression springs and 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


    HINT:
    A258966E01
    After installation, check that the space between the flanges of the center exhaust pipe assembly and tail exhaust pipe assembly is consistent front-to-rear and left-to-right.
    Text in Illustration 
    *1
    Tail Exhaust Pipe Assembly
    *2
    Center Exhaust Pipe Assembly
    *3
    Exhaust Pipe Gasket
    *a
    Space between Flanges: 6.5 mm (0.256 in.)



4. INSTALL HEATED OXYGEN SENSOR


    A335626E02
  1. Using SST, install the heated oxygen sensor to the front exhaust pipe assembly.
    Text in Illustration 
    *a
    Torque Wrench Fulcrum Length

    SST
    09224-00011  

    Torque:
    Specified tightening torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }

    NOTICE:
    If the heated oxygen sensor has been struck or dropped, replace it.

    HINT:
    1. Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
    2. When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 260 mm (10.2 in.)): 39 N*m (398 kgf*cm, 29 ft.*lbf)

  1. Connect the heated oxygen sensor connector.



5. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.
  1. Perform Inspection After Repair after repairing an exhaust gas leak (Click here).