Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Entry and Start System)

ENGINE IMMOBILISER SYSTEM (w/ Smart Entry and Start System) > HOW TO PROCEED WITH TROUBLESHOOTING

for Preparation Click here


HINT:
  1. Use this procedure to troubleshoot the engine immobiliser system.
  1. *: Use the intelligent tester.



1.VEHICLE BROUGHT TO WORKSHOP

    NEXT


    2.INSPECT BATTERY VOLTAGE
    1. Measure the battery voltage.

      Standard Voltage:
      11 to 14 V

      1. If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

      HINT:
      A simple method to determine whether the battery is discharged is to operate the horn.


    NEXT


    3.TURN ENGINE SWITCH ON (IG)

      HINT:
      If the engine switch cannot be turned on (IG), communication with the intelligent tester can be confirmed by connecting the intelligent tester to the DLC3 and turning a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins.


    NEXT


    4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
    1. Use the intelligent tester to check if the CAN communication system is functioning normally (Click here).

      Result:
      Result
      Proceed to
      CAN DTC is not output
      A
      CAN DTC is output
      B



    B.
    GO TO CAN COMMUNICATION SYSTEM (Click here)
    A


    5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
    1. Use the intelligent tester to check if the LIN communication system is functioning normally (Click here).

      Result:
      Result
      Proceed to
      LIN DTC is not output
      A
      LIN DTC is output
      B



    B.
    GO TO LIN COMMUNICATION SYSTEM (Click here)
    A


    6.CHECK FOR DTC*
    1. Check for DTCs and make a note of any codes that are output (Click here).

    2. Based on the DTCs output above, proceed to each diagnostic procedure.

      Result:
      Result
      Proceed to
      DTC is not output
      A
      SFI system DTC is output (for 2GR-FE)
      B
      SFI system DTC is output (for 2AR-FE)
      C
      SFI system DTC is output (for 6AR-FSE)
      D
      Steering lock system DTC is output
      E
      Engine immobiliser system DTC is output
      F



    B.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)

    C.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)

    D.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)

    E.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)

    F.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
    A


    7.PROBLEM SYMPTOMS TABLE
    1. Refer to Problem Symptoms Table (Click here).

      Result:
      Result
      Proceed to
      Fault is not listed in problem symptoms table
      A
      Fault is listed in problem symptoms table
      B



    B.
    go to step 9
    A


    8.OVERALL ANALYSIS AND TROUBLESHOOTING*
    1. Data List / Active Test (Click here)

    2. Terminals of ECU (Click here)


    NEXT


    9.REPAIR OR REPLACE

      NEXT


      10.CHECK FOR DTC*
      1. Clear the DTCs (Click here).

      2. Check for DTCs (Click here).

        HINT:
        Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure (Click here).

        Result:
        Result
        Proceed to
        DTC is not output
        A
        Engine immobiliser system DTC is output
        B



      B.
      GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
      A

      END