Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Front Side)

SIDE AIRBAG SENSOR (for Front Side) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. INSTALL DOOR SIDE AIRBAG SENSOR
  1. Check that the engine switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



  1. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.


    B296255E01


    Text in Illustration 
    *a
    Incorrect
    *b
    Correct

  1. Insert the pin (stopper) into the door hole and install the door side airbag sensor to the front door panel with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
    3. Make sure that the pin (stopper) is securely inserted into the body hole.
    4. Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.



  1. Connect the connector to the door side airbag sensor.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.




    1. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).


      H043305E12


      Text in Illustration 
      *1
      White Housing Lock
      *2
      Yellow CPA
      *a
      Connection is Completed
      -
      -

      HINT:
      When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and part (A), as it may result in an insecure fit.

  1. Check that there is no looseness in the installation parts of the door side airbag sensor.



2. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B380645E01
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly as shown in the illustration.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable Assembly
    *2
    Front Door Lock Remote Control Cable Assembly

  1. Engage the clamp.



    B380643E01
  1. Engage the 4 claws and reference boss as shown in the illustration.
    Text in Illustration 
    *a
    Reference Boss



    B380641
  1. Engage the 10 clips to install the front door trim board sub-assembly.

  1. Install the 3 screws.



3. INSTALL COURTESY LIGHT ASSEMBLY
  1. Connect the connector.



    E226715E01
  1. Engage the claw to install the courtesy light assembly.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



4. INSTALL FRONT ARMREST ASSEMBLY


    B277188
  1. Engage the 2 guides, 3 clips and 7 claws to install the front armrest assembly.



5. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
  1. Connect each connector.



    B380636
  1. Engage the 3 guides, 2 clips and 6 claws to install the power window regulator master switch assembly with front door armrest base panel.



6. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
  1. Connect each connector.



    B401213
  1. Engage the 3 guides, 2 clips and 6 claws to install the power window regulator switch assembly with front door armrest base panel.



7. INSTALL FRONT DOOR FRONT LOWER FRAME UPPER COVER


    B380639
  1. Engage the 2 guides and 2 claws to install the front door front lower frame upper cover.



8. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B381716
  1. Engage the 3 claws to install the front door inside handle bezel plug.



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



10. PERFORM DIAGNOSTIC SYSTEM CHECK
(Click here)


11. INSPECT SRS WARNING LIGHT
(Click here)