REAR AIRBAG SENSOR (for TMC, TMMR Made) > INSTALLATION |
| 1. INSTALL SIDE NO. 2 AIRBAG SENSOR ASSEMBLY |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

| *a | Incorrect | *b | Correct |
Insert the pin (stopper) into the body hole and install the side No. 2 airbag sensor assembly to the vehicle body with the bolt.
Connect the connector to the side No. 2 airbag sensor assembly.
Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

| *1 | White Housing Lock | *2 | Yellow CPA |
| *a | Connection is Completed | - | - |
Check that there is no looseness in the installation parts of the side No. 2 airbag sensor assembly.
| 2. INSTALL REAR SIDE SEATBACK ASSEMBLY (for Fold Down Seat Type) |
Place the rear side seatback assembly LH in the cabin.
Engage the hook to install the rear side seatback assembly LH with the bolt.
Connect the rear seat outer belt assembly to the rear seat shoulder belt guide LH.
| 3. INSTALL REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type) |
![]() |
Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.
| 4. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type) |
Place the rear seat cushion assembly in the cabin.
w/ Seat Heater System:
Engage the 2 clamps.
Connect the connector.
![]() |
Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.
Confirm that the rear seat cushion assembly is firmly installed.
| 5. INSTALL REAR SEAT SIDE GARNISH (for Reclining Seat Type) |
Engage the guide, claw and 2 clips.
Install the rear seat side garnish LH with the bolt.
| 6. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP (for Reclining Seat Type) |
| 7. INSTALL REAR DOOR SCUFF PLATE (for Reclining Seat Type) |
Engage the 6 claws to install the rear door scuff plate LH.
| 8. INSTALL REAR SEATBACK ASSEMBLY (for Reclining Seat Type) |
Place the rear seatback assembly LH in the cabin.
Install the rear seatback assembly LH with the 2 bolts and 2 nuts.
Engage the 2 hooks to install the cover.
Connect the 2 rear seat belts to the 2 rear seat shoulder belt guides.
w/ Rear Seat Side Airbag:
Connect each connector and clamp to the child restraint anchor bracket sub-assembly LH.
| 9. INSTALL REAR SEATBACK COVER (for Reclining Seat Type) |
Engage the 4 claws to install the 2 rear seatback covers.
| 10. INSTALL REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type) |
| 11. INSTALL REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type) |
![]() |
Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.
| 12. INSTALL REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type) |
Place the rear seat cushion assembly in the cabin.
Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly.
Connect the 2 seat heater connectors.
![]() |
Engage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly to the 2 rear seat cushion lock hooks as shown in the illustration.
Confirm that the rear seat cushion assembly is securely installed.
| 13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 14. PERFORM DIAGNOSTIC SYSTEM CHECK |
| 15. INSPECT SRS WARNING LIGHT |