REAR AIRBAG SENSOR (for TMC, TMMR Made) > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type) |
![]() |
Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
| a | 100 mm (3.94 in.) or less |
w/ Seat Heater System:
Disconnect the connector.
![]() |
Disengage the 2 clamps.
Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.
| 4. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type) |
![]() |
Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.
| 5. REMOVE REAR SIDE SEATBACK ASSEMBLY (for Fold Down Seat Type) |
Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide LH.
![]() |
Remove the bolt.
Disengage the hook and remove the rear side seatback assembly LH.
| 6. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type) |
![]() |
Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
| a | 100 mm (3.94 in.) or less |
Disconnect the 2 seat heater connectors.
Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.
| 7. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type) |
![]() |
Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.
| 8. REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type) |
| 9. REMOVE REAR SEATBACK COVER (for Reclining Seat Type) |
![]() |
Disengage the 4 claws and remove the 2 rear seatback covers.
| 10. REMOVE REAR SEATBACK ASSEMBLY (for Reclining Seat Type) |
w/ Rear Seat Side Airbag:
Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.
Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.
![]() |
Disengage the 2 hooks and disconnect the cover.
Remove the 2 nuts, 2 bolts and rear seatback assembly LH.
| 11. REMOVE REAR DOOR SCUFF PLATE (for Reclining Seat Type) |
![]() |
Disengage the 6 claws and remove the rear door scuff plate LH.
| 12. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP (for Reclining Seat Type) |
| 13. REMOVE REAR SEAT SIDE GARNISH (for Reclining Seat Type) |
![]() |
Remove the bolt.
Disengage the claw, 2 clips and guide and remove the rear seat side garnish LH.
| 14. REMOVE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Disconnect the connector from the side No. 2 airbag sensor assembly.
Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

| *1 | White Housing Lock | *2 | Yellow CPA |
| *a | Connector Lock is Released | - | - |
Push down the white housing lock again and disconnect the connector.
![]() |
Remove the bolt and side No. 2 airbag sensor assembly from the vehicle body.
After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

| *a | Incorrect | *b | Correct |