Home › General › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > INITIALIZATION



PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED

Necessary Procedures
Effect/Inoperative Function When Necessary Procedures are not Performed
See page
Correct the steering angle neutral point
Parking assist monitor system
Click here

NOTICE:
  1. After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 90 seconds before disconnecting the cable from the negative (-) battery terminal (for Radio and Display Type).
  2. After the ignition switch is turned off, the navigation receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal (for Navigation Receiver Type).


PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

Replacement Part
Necessary Procedure
Effect/Inoperative Function when Necessary Procedures are not Performed
See page
ECM
Perform Vehicle Identification Number (VIN) or frame number registration
MIL comes on
Click here for 2AR-FE
Click here for 2GR-FE
Click here for 6AR-FSE
ECM
Code registration (Engine immobiliser system)
Engine start
See Service Bulletin for the registration method.
  1. Throttle with motor body assembly
  2. Cleaning the deposits from the throttle with motor body assembly
  3. Engine assembly
  4. Cylinder head sub-assembly
  5. Camshaft (for intake or exhaust camshaft)
  6. Camshaft timing gear assembly
  7. Camshaft timing exhaust gear assembly
  8. Piston or piston ring
  9. Mass air flow meter sub-assembly
  10. Fuel injector assembly
  11. Fuel pump
  12. Air fuel ratio sensor
  13. Engine coolant temperature sensor
  14. Spark plug
  15. Ignition coil assembly
  16. Air leaks from intake system
  17. Gas leaks from exhaust system
  18. Knock control sensor
Inspection after repair
  1. Poor idle, etc.
  2. Engine start function, etc.
Click here for 2AR-FE
Click here for 2GR-FE
  1. Throttle body with motor assembly
  2. Cleaning the deposits from the throttle body with motor assembly
  3. Engine assembly
  4. Cylinder head sub-assembly
  5. Camshaft (for intake or exhaust camshaft)
  6. Camshaft timing gear assembly
  7. Camshaft timing exhaust gear assembly
  8. Piston or piston ring
  9. Mass air flow meter sub-assembly
  10. Fuel injector assembly (for port injection)
  11. Fuel injector assembly (for direct injection)
  12. Fuel pump (for low pressure side)
  13. Fuel pump (for high pressure side)
  14. Air fuel ratio sensor
  15. Engine coolant temperature sensor
  16. Spark plug
  17. Ignition coil assembly
  18. EGR valve assembly
  19. Air leaks from intake system
  20. Gas leaks from exhaust system
  21. Knock control sensor
Inspection after repair
  1. Poor idle, etc.
  2. Engine start function, etc.
Click here for 6AR-FSE
Automatic transaxle assembly
  1. Reset memory
  2. Input transaxle compensation code into TCM
  3. Perform road test to allow TCM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Click here for U660E Initialization
Click here for U660E Registration
  1. Valve body assembly
  2. Shift solenoid valve SL3 and/or SL4
  1. Reset memory
  2. Reset transaxle compensation code
  3. Perform road test to allow TCM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Shift solenoid valve SL1 and/or SL2
Perform road test to allow TCM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
TCM (If possible, read the transaxle compensation code from the previous TCM)
Possible
  1. Reset memory
  2. Transfer transaxle compensation code
  3. Perform road test to allow TCM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Impossible
  1. Reset memory
  2. Reset transaxle compensation code
  3. Perform road test to allow TCM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Automatic transaxle assembly
  1. Reset memory
  2. Input transaxle compensation code into ECM
  3. Perform road test to allow ECM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Click here for U760E Initialization
Click here for U760E Registration
Click here for U761E Initialization
Click here for U761E Registration
  1. Valve body assembly
  2. Shift solenoid valve SL3 and/or SL4
  1. Reset memory
  2. Reset transaxle compensation code
  3. Perform road test to allow ECM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Shift solenoid valve SL1 and/or SL2
Perform road test to allow ECM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
ECM (If possible, read the transaxle compensation code from the previous ECM)
Possible
  1. Reset memory
  2. Transfer transaxle compensation code
  3. Perform road test to allow ECM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Impossible
  1. Reset memory
  2. Reset transaxle compensation code
  3. Perform road test to allow ECM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
  1. Tire pressure warning ECU and receiver
  2. Tire pressure warning valve and transmitter
  1. Register Transmitter ID
  2. Initialize tire pressure warning system
  1. When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates
  2. Tire pressure warning function
Click here for Registration
Click here for Initialization
Skid control ECU (Brake actuator assembly)
Perform system variant learning
  1. Slip indicator light illumination
  2. VSC disabled or malfunctioning
Click here
Power steering ECU assembly
  1. Torque sensor zero point calibration
  2. Assist map writing
  1. P/S warning light comes on
  2. EPS control
Click here
Electric power steering column sub-assembly
Torque sensor zero point calibration
Steering effort is different between turning steering wheel to left and right
Steering sensor
  1. Steering angle neutral point (Initialize parking assist monitor system)
  2. Steering angle setting
Parking assist monitor system
Click here for Initialization
Click here for Calibration
Suspension, tires, etc.
Rear television camera assembly optical axis (Back camera position setting)
Parking assist monitor system
Rear television camera assembly
  1. Parking assist monitor system initialization
  2. Rear television camera assembly optical axis (Back camera position setting)
Parking assist monitor system
Blind spot monitor sensor
Blind spot monitor beam axis inspection
DTCs are output
Click here
  1. Certification ECU (smart key ECU assembly)*1
  2. ID code box (immobiliser code ECU)*1*5
  3. Steering lock ECU (steering lock actuator assembly)*1
  4. Telephone Transceiver Assembly*6
  5. Electrical key transmitter (key)*1
Code registration (Engine immobiliser system)
  1. Wireless door lock control system
  2. Smart entry and start system
  3. Engine start
  4. Steering lock system
See Service Bulletin for the registration method.
  1. Transponder key ECU assembly*2
  2. Door control transmitter assembly*2
Code registration (Engine immobiliser system)
Engine start
See Service Bulletin for the registration method.
  1. Door control transmitter*2
  2. Door control receiver*2
Code registration (Wireless door lock system)
Wireless door lock control system
Click here
  1. Occupant detection ECU*6
  2. Front passenger seat*6
Zero point calibration and sensitivity check (Occupant classification system)
  1. Occupant classification system
  2. Passenger airbag ON/OFF indicator
  3. Airbag system (Front passenger side)
  4. Seat belt warning system (Front passenger)
Click here
  1. No. 1 air conditioning radiator damper servo sub-assembly
  2. No. 2 air conditioning radiator damper servo sub-assembly
  3. No. 3 air conditioning radiator damper servo sub-assembly*7
  4. No. 1 blower damper servo sub-assembly
Servo motor initialization (Air conditioning system)
DTCs are output
Click here
  1. Door window regulator assembly*8
  2. Power window regulator motor assembly*8
  3. Door glass*8
  4. Door glass run*8
Initialize power window control system
  1. Auto up/down function
  2. Jam protection function
  3. Operation function after ignition switch is turned off
  4. Key-linked function
  5. Wireless transmitter-linked function
Click here
  1. Front door window regulator assembly*9
  2. Power window regulator motor assembly (for driver door)*9
  3. Power window regulator motor assembly (for front passenger door)*9
  4. Door glass*9
  5. Door glass run*9
Initialize power window control system
  1. Auto up/down function
  2. Jam protection function
  3. Operation function after ignition switch is turned off
  4. Key-linked function
  5. Wireless transmitter-linked function
Click here
  1. Sliding roof ECU (sliding roof drive gear sub-assembly)
  2. Sliding roof glass sub-assembly
  3. Sliding roof drive cable sub-assembly
Initialize sliding roof ECU (pulse sensor initial position setting)
  1. Automatic slide open/close and tilt up/down function of sliding roof
  2. Jam protection function
  3. Operation function after ignition switch is turned off
  4. Key-linked function
  5. Wireless transmitter-linked function
  6. Sliding roof open warning
Click here
  1. AFS ECU (headlight swivel ECU assembly)*3
  2. Rear height control sensor sub-assembly*3
Perform AFS ECU initialization
AFS function
Click here
  1. Headlight leveling ECU assembly*4
  2. Rear height control sensor sub-assembly*4
Perform Headlight leveling ECU initialization
Automatic headlight beam level control function
Click here
  1. *1: w/ Smart Entry and Start System
  2. *2: w/o Smart Entry and Start System
  3. *3: w/ AFS (Adaptive Front-lighting System)
  4. *4: w/ Automatic Headlight Beam Level Control System
  5. *5: w/o Wireless Door Lock Buzzer Answer Back Function
  6. *6: w/ Occupant Classification System
  7. *7: for 3 Zone Type
  8. *8: for Models with Jam Protection Function on 4 Windows
  9. *9: for Models with Jam Protection Function on Front Door Windows