Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › KNEE AIRBAG ASSEMBLY (for TMMK Made Driver Side)

KNEE AIRBAG ASSEMBLY (for TMMK Made Driver Side) > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing (Click here).

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT DOOR SCUFF PLATE LH


    B395175E01
  1. Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.

  1. Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.

  1. Disengage the 6 claws (C) to remove the front door scuff plate LH.



4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B278978
  1. Remove the clip.

  1. Pull the cowl side trim sub-assembly LH as shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.



5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Disconnect the front door opening trim weatherstrip LH to the extent that allows the removal of the instrument side panel LH.



6. REMOVE INSTRUMENT SIDE PANEL LH


    B377599
  1. Using a moulding remover, disengage the 4 claws as shown in the illustration.



    B399733
  1. Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.



7. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B279865
  1. Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.



8. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    B403736
  1. Remove the bolt <B> and screw <C> or <D>.



    B377614
  1. Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.



9. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

CAUTION:
When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.

  1. Check that the engine switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B279717
  1. Remove the 4 bolts.

  1. Disengage the 2 claws to disconnect the DLC3.



    B279758
  1. Disengage the 2 hooks to remove the lower No. 1 instrument panel airbag assembly.

    NOTICE:
    When removing the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.



    B279718E01
  1. Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Airbag Connector
    *3
    Airbag Connector Lock

  1. Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.