Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Tachometer Malfunction

for Preparation Click here


DESCRIPTION

In this circuit, the combination meter assembly receives engine speed signals from the ECM using the CAN communication system. The combination meter assembly displays the engine speed calculated based on the data received from the ECM.

WIRING DIAGRAM


E143765E66


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here).

    Result:
    Result
    Proceed to
    CAN communication DTC is not output.
    A
    CAN communication DTC is output.
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.PERFORM ACTIVE TEST USING GTS (TACHO METER OPERATION)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Tacho Meter Operation
    Tachometer
    OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000, 7000
    -

    OK:
    Tachometer indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.CHECK SFI SYSTEM
  1. Check if SFI system DTCs are output (Click here for 2AR-FE, Click here for 2GR-FE, Click here for 6AR-FSE).

    Result:
    Result
    Proceed to
    SFI system DTCs not output.
    A
    SFI system DTCs output (for 2AR-FE).
    B
    SFI system DTCs output (for 2GR-FE).
    C
    SFI system DTCs output (for 6AR-FSE).
    D



B
GO TO SFI SYSTEM (Click here)

C
GO TO SFI SYSTEM (Click here)

D
GO TO SFI SYSTEM (Click here)
A


4.READ VALUE USING GTS (ENGINE SPEED, ENGINE RPM)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus:

    1. for Engine and ECT: Powertrain / Engine and ECT / Data List.

    2. for Combination Meter: Body Electrical / Combination Meter / Data List.

  1. Read the Data List according to the display on the GTS.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Stored as Freeze Frame Data
    Engine Speed
    Engine speed/Min.: 0 rpm, Max.: 16383 rpm
    for 2GR-FE:
    600 to 700 rpm: Idling
    for 2AR-FE:
    610 to 710 rpm: Idling
    for 6AR-FSE:
    600 to 700 rpm: Idling (shift lever in P, engine warmed up and A/C off)
    Yes
    Results of real-vehicle check (for 2GR-FE, 2AR-FE):
    Idling (engine warmed up and A/C off): 660 rpm
    Diagnostic Note:
    When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Rpm
    Engine speed/Min.: 0 rpm, Max.: 12750 rpm
    Almost the same as actual engine speed
    -

    Result:

    Result
    Proceed to
    The data list values of the ECUs match.
    A
    The data list values of the ECUs do not match (for 2AR-FE).
    B
    The data list values of the ECUs do not match (for 2GR-FE).
    C
    The data list values of the ECUs do not match (for 6AR-FSE).
    D

    HINT:
    1. When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.
    2. When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.



B
GO TO SFI SYSTEM (Click here)

C
GO TO SFI SYSTEM (Click here)

D
GO TO SFI SYSTEM (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)