Home › Drivetrain ยท U761E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > ROAD TEST

for Preparation Click here



PROBLEM SYMPTOM CONFIRMATION
  1. Based on the result of the customer problem analysis, try to reproduce the symptoms. If the problem is that the transaxle does not shift up, shift down, or the shift point is too high or too low, conduct the following road test referring to the automatic shift schedule and simulate the problem symptoms.


ROAD TEST
  1. Perform a road test.

    CAUTION:
    Check for safety before performing any tests.

    NOTICE:
    1. Be sure to inspect and adjust the engine before performing these tests.
    2. Perform the road test with the engine coolant temperature between 60 and 100°C (140 and 212°F) and the ATF temperature between 50 and 100°C (122 and 212°F).
    3. Perform these tests with the air conditioning and cruise control off.


    Inspection
    Procedure
    Transmission Control Switch Test
    With the vehicle stationary and the shift lever in D, move the shift lever to S and return it to D. Check that the meter display changes from D to the appropriate S range and then back again.
    S Position Test
    With the vehicle stationary and the shift lever in S, move the shift lever to "+" and "-". Check that the meter display changes between S ranges properly.
    D Position Shift Test
    While driving the vehicle normally, check that the transmission shifts up and down through each gear properly.
    Lock-up Function
    While driving on a level surface at a constant speed in the lock-up range with the shift lever in D, lightly depress the accelerator pedal and check that the engine speed does not change abruptly.
    P Position Test
    Stop the vehicle on an incline (approximately 5° or more). Move the shift lever to P and release the parking brake. Check that the parking lock pawl holds the vehicle in place.
    Abnormal Noise and Vibration
    Check for abnormal noise and vibration while driving the vehicle forward and backward, and during shift operations.
    Fluid Leakage
    After performing all other road test inspections, check for fluid leakage.

    HINT:
    When checking for DTCs after a repair, drive the vehicle according to the monitor drive pattern (Click here).

  2. Shift schedule confirmation

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Powertrain / Engine / Data List / Vehicle Speed, Throttle Sensor Position and Shift Status.

    4. Check that the "Shift Status" changes in accordance with the "Vehicle Speed" as shown in the following table.

      Shift Schedule Chart:

      Throttle Sensor Position
      9 +/- 1%
      Shift Status
      (Shift Lever in D)
      1st to 2nd
      2nd to 3rd
      3rd to 4th
      4th to 5th
      5th to 6th
      Vehicle Speed
      5 to 20 km/h
      (3 to 12 mph)
      15 to 30 km/h
      (9 to 19 mph)
      25 to 45 km/h
      (16 to 28 mph)
      40 to 60 km/h
      (25 to 37 mph)
      60 to 80 km/h
      (37 to 50 mph)

      NOTICE:
      1. All vehicle speeds indicated in the above table are actual values. Therefore, if checking a shift point with a chassis dynamometer, keep in mind that there is a margin of error in the chassis dynamometer indication.
      2. If checking a shift point against the vehicle speed indicated on the speedometer, remember to consider the speedometer correction rate and margin of error in the tester indication.

  3. Lock-up confirmation

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Powertrain / Engine / Data List / Vehicle Speed, Engine Speed, Throttle Sensor Position, NT Sensor Speed, A/T Oil Temperature No. 1, Lock Up Status and Shift Status.

    4. When the following conditions are met, check that the difference between "Engine Speed" and "NT Sensor Speed" is 50 rpm or less.
      Lock-up Schedule 
      Throttle Sensor Position
      9 +/- 1%
      Vehicle Speed
      80 km/h (50 mph) or more
      Shift Status
      6th gear
      Lock Up Status
      ON

      HINT:
      Lock-up prohibition conditions:
      1. Engine coolant temperature is less than 45°C (113°F)
      2. Vehicle is being driven with the S1, S2 or S3 range selected
      3. Throttle valve is fully closed
      4. Stop light switch is on

  4. Manual down-shift permission speed

    1. Manual down-shift is permitted for each shift status when the vehicle speed is below the corresponding range shown in the following table.

      Manual Down-shift Permission Speed Chart:

      Shift Status
      (Shift Lever in S)
      6th to 5th
      5th to 4th
      4th to 3rd
      3rd to 2nd
      2nd to 1st
      Vehicle Speed
      245 to 300 km/h
      (152 to 186 mph)
      175 to 215 km/h
      (109 to 134 mph)
      125 to 155 km/h
      (78 to 96 mph)
      90 to 115 km/h
      (56 to 71 mph)
      40 to 55 km/h
      (25 to 34 mph)

  5. Shift schedule when throttle valve is fully open

    Shift Schedule Chart:

    Throttle Opening Angle
    Throttle Valve Fully Open
    Shift Status
    (Shift Lever in D)
    1st to 2nd
    2nd to 3rd
    3rd to 4th
    4th to 5th
    5th to 6th
    Vehicle Speed
    30 to 60 km/h
    (19 to 37 mph)
    80 to 110 km/h
    (50 to 68 mph)
    115 to 145 km/h
    (72 to 90 mph)
    170 to 205 km/h
    (106 to 127 mph)
    235 to 270 km/h
    (147 to 168 mph)