Home › Drivetrain · U761E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P271313    Pressure Control Solenoid "D" Circuit Open

for Preparation Click here


DESCRIPTION

The shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The ECM adjusts the current to the shift solenoid valve SLT to control hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

DTC No.
DTC Detection Condition
Trouble Area
P271313
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
  1. The engine is running.
  2. An open or short in the shift solenoid valve SLT circuit is detected.
  3. 1 second
  4. 1-trip detection logic
  1. Wiring harness connector
  2. Open or short in shift solenoid valve SLT circuit
  3. Shift solenoid valve SLT
  4. ECM

MONITOR DESCRIPTION

When an open or short in the linear solenoid valve SLT circuit is detected, the ECM interprets this as a malfunction, illuminates the MIL and stores this DTC.

WIRING DIAGRAM


C314405E04


INSPECTION PROCEDURE

NOTICE:
Perform registration and/or initialization when parts related to the automatic transaxle are replaced (Click here).

HINT:
After inspection repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Start the engine.
  2. Check for DTCs again (Click here).

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SLT CIRCUIT)
  1. Disconnect the E96 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E96-1 (SLT+) - E96-31 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    E96-1 (SLT+) - Body ground and other terminals
    Always
    10 kΩ or higher
    E96-31 (SLT-) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
Go to step 2
OK

REPLACE ECM (Click here)  

2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
  1. Disconnect the E8 connector from the wiring harness connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E96-1 (SLT+) - E8-15 (SLT+)
    Always
    Below 1 Ω
    E96-31 (SLT-) - E8-7 (SLT-)
    Always
    Below 1 Ω
    E96-1 (SLT+) or E8-15 (SLT+) - Body ground and other terminals
    Always
    10 kΩ or higher
    E96-31 (SLT-) or E8-7 (SLT-) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT TRANSMISSION WIRE (SLT)


    C315790E07
  1. Remove the wiring harness connector.
    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-12 (SLT+) - A-7 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    A-12 (SLT+) - Body ground and other terminals
    Always
    10 kΩ or higher
    A-7 (SLT-) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
Go to step 4
OK

REPLACE WIRING HARNESS CONNECTOR (Click here)  

4.INSPECT SHIFT SOLENOID VALVE SLT


    C201747E01
  1. Remove the shift solenoid valve SLT.
    Text in Illustration 
    *1
    Shift Solenoid Valve SLT

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

    OK:
    Valve moves and makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)