STEERING COLUMN ASSEMBLY > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column) |
Disable the auto tilt away function by changing the customize parameter (Click here).
Turn the ignition switch to ON. Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.
Turn the ignition switch off and disconnect the cable from the negative (-) battery terminal.
| 3. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD |
| 4. REMOVE FRONT WHEEL LH |
| 5. REMOVE HORN BUTTON ASSEMBLY |
| 6. REMOVE STEERING WHEEL ASSEMBLY |
![]() |
Remove the steering wheel assembly set nut.
| *a | Matchmark |
Put matchmarks on the steering wheel assembly and steering main shaft.
Disconnect the connectors from the spiral cable sub-assembly.
![]() |
Using SST, remove the steering wheel assembly.
| *a | Turn |
| *b | Hold |
| 7. REMOVE FRONT DOOR SCUFF PLATE (w/o Driver Side Knee Airbag) |
![]() |
Disengage the 10 claws and remove the front door scuff plate LH.
| 8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY (w/o Driver Side Knee Airbag) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 9. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP (w/o Driver Side Knee Airbag) |
![]() |
Disconnect the front door opening trim weatherstrip LH.
| 10. REMOVE INSTRUMENT SIDE PANEL (w/o Driver Side Knee Airbag) |
![]() |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
| 11. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (w/o Driver Side Knee Airbag) |
![]() |
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
| 12. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag) |
![]() |
Remove the 2 bolts <B>.
w/o Driver Side Knee Airbag:
![]() |
Disengage the 5 clips and 3 guides to remove the instrument panel sub-assembly.
w/ Driver Side Knee Airbag:
![]() |
Disengage the 4 claws, 7 clips and 3 guides to remove the instrument panel sub-assembly.
| 13. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag) |
| 14. REMOVE LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column) |
![]() |
Remove the 2 screws.
![]() |
Push the right and left sides of the lower steering column cover, and disengage the 2 claws.
![]() |
Insert a finger into the opening of the tilt lever of the lower steering column cover to disengage the claw and remove the lower steering column cover.
| 15. REMOVE LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column) |
![]() |
Remove the 3 screws.
![]() |
Push the right and left sides of the lower steering column cover, and disengage the 2 claws to remove the lower steering column cover.
| 16. REMOVE UPPER STEERING COLUMN COVER |
![]() |
Disengage the 4 clips and 2 guides from the upper steering column cover.
![]() |
Disengage the 2 claws to remove the upper steering column cover.
| 17. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.
![]() |
Disengage the 3 claws to remove the turn signal switch assembly with spiral cable sub-assembly from the steering post assembly.
| 18. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Using a screwdriver, loosen the clamp as shown in the illustration.
![]() |
Put matchmarks on the steering intermediate shaft assembly and the steering link assembly.
| *a | Matchmark |
Remove the bolt and separate the steering intermediate shaft assembly from the steering link assembly.
| 19. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY (for LHD) |
for TMC, TMMR Made:
![]() |
Disengage the wire harness clamp from the No. 2 air duct sub-assembly.
| *1 | Guide |
| *2 | Clamp |
| *3 | Claw |
Disconnect the connector from the footwell light.
Using a screwdriver, disengage the 2 claws and guide.
Disengage the clamp to remove the No. 2 air duct sub-assembly.
for TMMK Made:
![]() |
Disengage the 2 claws and guide to remove the No. 2 air duct sub-assembly.
| *1 | Guide |
| *2 | Claw |
| 20. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY (for RHD) |
![]() |
Disconnect the connector from the footwell light.
Remove the bolt.
Disengage the 2 claws to remove the No. 2 air duct sub-assembly.
| 21. REMOVE STEERING POST ASSEMBLY |
Disconnect the connectors and disengage the wire harness clamps from the steering post assembly.
![]() |
Disconnect the 2 connectors.
![]() |
Disengage the clamp.
for Manual Tilt and Manual Telescopic Steering Column
![]() |
Remove the bolt to separate the ground wire.
Remove the 4 nuts and the steering post assembly.
for Power Tilt and Power Telescopic Steering Column
![]() |
Remove the bolt to separate the ground wire.
Remove the 4 nuts and the steering post assembly.
| 22. REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Remove the bolt and slide the steering intermediate shaft assembly.
| *a | Matchmark |
Put matchmarks on the steering intermediate shaft assembly and the steering post assembly.
Remove the steering intermediate shaft assembly from the steering column assembly.