CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to +B (RHD Models) |
| Symptom | Trouble Area |
| No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of DLC3. |
|


| 1.CHECK FOR SHORT TO +B IN CAN BUS LINE (DLC3 BRANCH LINE) |
Disconnect the cable from the negative (-) battery terminal.
![]() |
Disconnect the DLC3 branch line connector (I96) from the CAN No. 2 junction connector.
| *a | Rear view of wire harness connector (to CAN No. 2 Junction Connector) |
| *b | to DLC3 |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | |
| 2.CHECK FOR SHORT TO +B IN CAN BUS LINE |
Reconnect the DLC3 branch line connector (I96) to the CAN No. 2 junction connector.
![]() |
Disconnect the connectors (I94, I95, I97, I100, I102, I103, I104, I105, I106, I07 and I111) from the CAN No. 1 junction connector and CAN No. 2 junction connector one at a time.
| *1 | DLC3 |
Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.

| *A | for Radio and Display Type | - | - |
| *1 | Clearance Warning ECU Assembly | *2 | Steering Sensor |
| *3 | Brake Actuator Assembly | *4 | Smart Key ECU Assembly (Certification ECU) |
| *5 | DLC3 | *6 | Combination Meter Assembly |
| *7 | Radio and Display Receiver Assembly | *8 | ECM |
| *9 | Power Steering ECU with Motor Assembly | *10 | Airbag Sensor Assembly |
| *11 | Air Conditioning Amplifier Assembly | *12 | Main Body ECU (Multiplex Network Body ECU) |
| *13 | CAN No. 1 Junction Connector | *14 | CAN No. 2 Junction Connector |

| *a | Component without harness connected (CAN No. 1 Junction Connector) | - | - |
| CAN No. 1 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
| Main body ECU (Multiplex network body ECU) | I95 | P | W |
| Air conditioning amplifier assembly | I102 | V | W |
| Airbag sensor assembly | I103 | Y | W |
| Power steering ECU with motor assembly | I100 | L | W |
| ECM | I104 | G | W |
| Radio and display receiver assembly* | I107 | R | W |
| CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) | I93 | B | W |

| *a | Component without harness connected (CAN No. 2 Junction Connector) | - | - |
| CAN No. 2 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
| CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) | I101 | B | W |
| Combination meter assembly | I94 | R | W |
| DLC3 | I96 | G | W |
| Smart key ECU assembly (Certification ECU) | I106 | L | W |
| Brake actuator assembly | I105 | Y | W |
| Steering sensor | I97 | V | W |
| Clearance warning ECU assembly | I111 | P | W |
| Symptom | Proceed to |
| The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector. (There is a short to +B in the CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.) | A |
| The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector. (There is a short to +B in one of the areas that relate to one or more of the disconnected bus lines.) | B |
When there is a short to +B in one or more of the bus lines that connect to an ECU or sensor:
Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to +B). Check that the resistance shown on the tester is normal (6 kΩ or higher) to confirm that there is a short to +B in the one bus line only.
When there is no short to +B in any of the bus lines that connect to the ECUs and sensors:
With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.
|
| ||||
| A | |
| 3.CHECK CAN NO. 2 JUNCTION CONNECTOR |
![]() |
Disconnect the CAN main bus line connector (I101) from the CAN No. 2 junction connector.
| *a | Rear view of wire harness connector (to CAN No. 2 Junction Connector) |
| *b | to CAN No. 1 Junction Connector |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | |
| 4.CHECK CAN NO. 1 JUNCTION CONNECTOR |
Reconnect the CAN main bus line connector (I101) to the CAN No. 2 junction connector.
![]() |
Disconnect the CAN main bus line connector (I93) from the CAN No. 1 junction connector.
| *a | Rear view of wire harness connector (to CAN No. 1 Junction Connector) |
| *b | to CAN No. 2 Junction Connector |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||
| 5.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR) |
Reconnect the connector of the bus line that is shorted to +B to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or higher when it was disconnected).
Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU or sensor to which the bus line shorted to +B is connected (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||