Home › Drivetrain · U761E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > Transmission Control Switch Circuit

for Preparation Click here


DESCRIPTION

When the shift lever is in S and moved toward "-" or "+", it is possible to select different shift ranges (S1 to S6).
Moving the shift lever toward "+" selects the next higher shift range, and moving the shift lever toward "-" selects the next lower shift range.

WIRING DIAGRAM


C311455E01


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following procedure.
  2. Perform registration and/or initialization when parts related to the automatic transaxle are replaced (Click here).

1.READ VALUE USING GTS (SPORT SHIFT SWITCH STATUS)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List.

  1. Read the Data List according to the display on the GTS.

    Engine 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Sport Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Continuously shift to "+" (Up shift)
    2. OFF: Release "+" (Up shift)
    -
    Sport Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Continuously shift to "-" (Down shift)
    2. OFF: Release "-" (Down shift)
    -

Result:
Result
Proceed to
Data List values are not normal
A
Data List values are normal
B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
  1. Disconnect the I44 transmission control switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    l44-4 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    l44-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH)


    C239095E33
  1. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Control Switch (Lower Shift Lever Assembly))

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (IG) - 5 (S)
    Shift lever in S, "+" or "-"
    Below 1 Ω
    Shift lever not in S, "+" or "-"
    10 kΩ or higher
    3 (SFTU) - 2 (E)
    Shift lever held in "+"
    (Up shift)
    Below 1 Ω
    Shift lever not held in "+"
    10 kΩ or higher
    1 (SFTD) - 2 (E)
    Shift lever held in "-"
    (Down shift)
    Below 1 Ω
    Shift lever not held in "-"
    10 kΩ or higher



NG
REPLACE LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH) (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
  1. Connect the I44 transmission control switch connector.

  1. Disconnect the A84 ECM connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A84-59 (S) - Body ground
    1. Engine switch on (IG)
    2. Shift lever in S, "+" or "-"
    11 to 14 V
    A84-59 (S) - Body ground
    1. Engine switch on (IG)
    2. Shift lever not in S, "+" or "-"
    Below 1 V

  1. Turn the engine switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A84-42 (SFTU) - Body ground
    Shift lever held in "+"
    (Up shift)
    Below 1 Ω
    Shift lever not held in "+"
    10 kΩ or higher
    A84-43 (SFTD) - Body ground
    Shift lever held in "-"
    (Down shift)
    Below 1 Ω
    Shift lever not held in "-"
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)